2-9
IN
O
U
T
R
E
M
O
T
E
2
AC IN
A
UD
IO
A
U
D
I
O
O
U
T
R
R
/C
r
G
/Y
B/
Cb
V
H
/
H
V
R
L
/M
O
N
O
R
L
/
M
ON
O
R
L
/
M
O
N
O
L
/
M
O
N
O
DVI
R
GB
OUT
RGB 1
RGB 2
VIDEO
S-VIDEO
A
U
DIO
S
LOT
1
S
L
OT
2
3
4
IN
O
U
T
R
EM
O
T
E
2
A
C
IN
A
U
D
IO
A
U
D
IO
O
U
T
R
R
/C
r
G
/Y
B
/
C
b
V
H
/H
V
R
L
/
M
O
N
O
R
L
/M
O
N
O
R
L
/
M
O
N
O
L
/M
O
N
O
DVI
R
G
B
O
U
T
RGB 1
RGB 2
VIDEO S-VIDEO
A
U
D
IO
S
LOT
1
S
LO
T
2
2
1
4. Reinstall the lens hood.
q Remove the front lens cap from the lens unit.
w Insert the lens hood so that the grooves on the 4 corners of the lens hood
are properly lined up with the 4 catches on the projector.
e Secure the 2 screws using the hexagonal driver.
This completes installation. If necessary, put the lens hood cap on the lens
hood.
P
C
C
O
N
T
R
O
L
I
N
IN
O
U
T
O
S
C
T
R
IG
G
E
R
R
E
M
O
T
E
2
R
E
M
O
T
E
1
L
A
N
A
C
IN
U
S
B
(
M
O
U
SE/H
U
B
)
U
S
B
(
P
C
)
P
C
C
A
R
D
1
2
A
U
D
IO
A
U
D
IO
O
U
T
R
R
/C
r
G
/Y
B
/C
b
V
H
/
H
V
R
L
/
M
O
N
O
R
L
/
M
O
N
O
R
L
/
M
O
N
O
L
/
M
O
N
O
D
V
I
R
G
B
O
U
T
R
G
B 1
R
G
B
2
VID
EO
S
-V
ID
E
O
A
U
D
IO
S
L
O
T
1
S
L
O
T
2
3
2
P
C
S
C
U
S
B
(
MOU
SE
/H
UB
)
A
UDIO
O
O
U
T
R
R/C
r
G/Y
B
/C
b
V
H
/
H
V
R
L
/
M
O
N
O
R
L
/
M
O
N
O
R
L
/
M
O
N
O
L
/
M
O
N
O
D
VI
R
G
B
O
U
T
R
G
B 1
R
GB 2
VID
EO
S-VID
EO
A
UDIO
S
L
O
T
1
S
L
O
T
2
1
Lens shift defection switch
2. Installation
3. Mount the lens unit on the projector and connect the extension cable attached to the projector.
q Remove the lens cap from the rear end of the lens unit.
NOTE: Leave the front lens cap for protection while mounting the lens unit.
w Insert the lens unit so that the 4 screws on the lens unit are properly lined up with the 4 holes on the lens mount.
CAUTION:There is a lens shift detection switch for the moving gears of the lens shift motors used to reduce the risk of pinching fingers.
Do not defeat this feature.
e Secure the 4 screws using the hexagonal driver.
r Insert the connector of the lens unit fully into the socket of the extension cable attached to the projector.