Filter
Top Products
ISDN Features
Primary Rate Interface (PRI), Answering Calls
Aspire ISDN PRI Manual ◆ 19
Programming (Cont’d)
➻
15-02-02 : Multi-Line Telephone Basic Data Setup - Trunk Ring Tone
Use this option to change the ringing pitch of incoming trunk calls to keysets.
Default Setting: Midrange (2)
➻ 15-06-01 : Trunk Access Map for Extensions
Assign Trunk Access Maps (200) to extensions. You must set up the Trunk Access Maps in Program
14-07-01. See How the Telco Handles PRI Trunks on page 12 for more.
Default Setting: All extensions use Access Map 1.
➻ 15-07-01 : Programmable Function Keys
To have incoming PRI calls ring specific keys, assign trunks to line keys (*01 + line # [001-200]). You
can also have loop keys (code *05) and Trunk Group keys (code *02 + Trunk Group).
Default Setting: Function keys 1-12 are line keys for trunks 1-12.
➻ 20-06-01 : Class of Service for Extensions
Assign a Class of Service (1-15) to an extension.
Default Setting: Extension 301 has COS 15. All other extension have COS 1.
➻ 20-09-03 : Class of Service Options (Incoming Call Service) - Sub-Address Identification
Enable (1) or disable (0) the telco’s ability to display the sub-address identification.
Default Setting: ISDN Sub-Address Identification disabled (0).
➻ 20-13-23 : Class of Service Options (Supplementary Service) - Display the Reason for Transfer
Enable (1) or disable (0) an extension’s ability to display the reason (Call Forward, Busy, No Answer or
DND) a VRS, DID, DISA, or ISDN call is being transferred to their extension.
Default Setting: No reason is displayed (0).
➻ 20-15-01 : Ring Cycle Setup - Normal Incoming Call on Trunk
Use this option to change the way calls ring the telephones. Keep in mind that changing this option
affects all types of trunk calls - not just PRI calls.
Default Setting: Outside calls ring keysets with a short ring followed by a pause (3).
➻ 20-19-04 : System options for Caller ID - Wait Facility IE Timer
This option sets how long the system will wait for the Caller ID name (0-64800 seconds). If set to “0”
no name is provided.
Default Setting: 10 seconds.
➻ 21-01-03 : System Options for Outgoing Calls - Trunk Interdigit Time (External)
Set the amount of time the system must wait before placing the call in a talk state (call isn't timed until
then, Voice Over and Barge-In are not allowed until after timer expires) (0-64800 seconds).
Default Setting: Trunk Interdigit = 5 seconds.
➻ 22-01-02 : System Options for Incoming Calls - Incoming Call Ring No Answer Alarm
Enable (1) or disable (0) the Incoming Call RNA Alarm. If enabled, the ring cadence will change for a
call that rings longer than the interval set in Program 22-01-03.
Default Setting: Incoming Ring No Answer Alarm disabled (0).
➻ 22-01-03 : System Options for Incoming Calls - Ring No Answer Alarm Time
Set the Ring No Answer Alarm interval (0-64800 seconds). If a trunk rings a keyset longer than this
interval, the system changes the ring cadence, if enabled in 22-01-02.
Default Setting: Ring No Answer Alarm Time = 60 seconds.
➻ 22-01-04 : System Options for Incoming Calls - DIL No Answer Recall Time
If an incoming trunk call rings longer than this interval, it reroutes to the Ring Group set in Program 22-08.
Default Setting: DIL No Answer Time disabled (0). Calls do not reroute.