Filter
Top Products
Chapter 2 Getting Started — Connecting
ENGLISH - 39
Connecting
Before connecting
f Before connecting, carefully read the operating instructions for the external device to be connected.
f Turn off the power of all devices before connecting cables.
f Take note of the following points before connecting the cables. Failure to do so may result in malfunctions.
g When connecting a cable to a device connected to the projector or the projector itself, touch any nearby metallic objects to eliminate static
electricity from your body before performing work.
g Do not use unnecessarily long cables to connect to a device connected to the projector or to the projector body. The longer the cable, the
more it is susceptible to noise. Since using a cable while it is wound makes it act like an antenna, it is more susceptible to noise.
g When connecting cables, connect GND rst, then insert the connecting terminal of the connecting device in a straight manner.
f Acquire any connection cable necessary to connect the external device to the system that is neither supplied with the device nor available
as an option.
f If video signals from video equipment contain too much jitter, the images on the screen may wobble. In this case, a time base corrector
(TBC) must be connected.
f The projector accepts video signals, Y/C signals, YC
B
C
R
/YP
B
P
R
signals, analog RGB signals (synchronization signals are TTL level), and
digital signals.
f Some computer models or graphics cards are not compatible with the projector.
f Use a cable compensator when you connect devices to the projector using long cables. Otherwise the image may not display properly.
f Refer to “List of compatible signals” (x page 146) for the types of video signals that can be used with the projector.
<RGB 1 IN> terminal pin assignments and signal names
Outside view Pin No. Signal name Pin No. Signal name
(10)
(6)
(11) (15)
(1) (5)
(1)
R/P
R
(9)
―
(2)
G/Y
(10)
GND
(3)
B/P
B
(11)
GND
(4)
―
(12)
DDC data
(5)
GND
(13)
SYNC/HD
(6)
GND
(14)
VD
(7)
GND
(15)
DDC clock
(8)
GND
<MONITOR OUT> terminal pin assignments and signal names
Outside view Pin No. Signal name Pin No. Signal name
(10)
(6)
(11) (15)
(1) (5)
(1)
R/P
R
(9)
―
(2)
G/Y
(10)
GND
(3)
B/P
B
(11)
GND
(4)
―
(12)
―
(5)
GND
(13)
SYNC/HD
(6)
GND
(14)
VD
(7)
GND
(15)
―
(8)
GND
<HDMI IN> terminal pin assignments and signal names
Outside view Pin No. Signal name Pin No. Signal name
Even-numbered pins of (2) to (18)
(1) (19)
(2) (18)
Odd-numbered pins of (1) to (19)
(1)
T.M.D.S data 2+
(11)
T.M.D.S clock shield
(2)
T.M.D.S data 2 shield
(12)
T.M.D.S clock
-
(3)
T.M.D.S data 2
-
(13)
CEC
(4)
T.M.D.S data 1+
(14)
—
(5)
T.M.D.S data 1 shield
(15)
SCL
(6)
T.M.D.S data 1
-
(16)
SDA
(7)
T.M.D.S data 0+
(17)
DDC/CEC
GND
(8)
T.M.D.S data 0 shield
(18)
+5 V
(9)
T.M.D.S data 0
-
(19)
Hot plug detection
(10)
T.M.D.S clock+