Filter
Top Products
GTX
PAGE 11
CENTURY SERIES
EQ IN Switch
Inserts the EQ section into the input channel (post insert, pre
fader). An associated green LED illuminates when the switch
is down.
AUX SENDS 1&2 and 3&4 Individual
Level Controls
Adjusts signal level sent to respective Aux buses. The signal
source for these mixes may be selected pre or post fader by an
associated switch. AUX pairs 1&2 and 3&4 are configured as
dual concentric pots with the inner knobs controlling the odd
sends (1&3), and the outer knobs controlling the even sends
(2&4).
PRE/POST Switch
Switches the Aux 1&2 and Aux 3&4 signal sources between
pre and post fader positions.
AUX SENDS 5-8
Individual Level Controls
Adjusts signal level sent to respective Aux buses. The signal
source for these mixes may be selected pre or post fader by the
associated AUX 5&6 PRE/POST or AUX 7&8 PRE/POST
switches.
Aux 8 Direct Switch
Removes the Aux 8 signal from the Aux 8 bus, and assigns the
signal to the direct out 1/4" connector on the rear panel, instead
of the normal post fader Dir Out signal.
AUX 5&6 PRE/POST Switch
Switches the Aux 5 & 6 signal sources between pre and post-
fader.
AUX 7&8 PRE/POST Switch
Switches the Aux 7 & 8 signal sources between pre and post-
fader
PAN CONTROL
Positions the channel image between left and right or between
left-center-right. (See L-C-R Switch)
MUTE Switch with LED
Mutes the channel and all send functions. Mute does not affect
the PFL switch or the Peak and Signal Present LED indicators.
Red LED illuminates when the channel is muted.
MONO Bus Assign Switch
Assigns the input signal directly to the Center / Mono bus.
L-C-R Switch
Configures Left/Right and Center/Mono assignments for L-C-
R panning. To enable L-C-R panning, L-R and Mono assign
switches must be down.
PAN Switch / Group Assign
Switches (1-8)
With PAN switch down, the PAN control varies the level of
the group assignments with odd numbered groups on the left
and even numbered groups on the right. With PAN switch up,
groups can be individually selected and are unaffected by the
PAN control. Group assign switches route signals to the Group
buses.
PFL Switch
Samples the channel’s signal (pre-fader) and allows for moni-
toring within the master section of the console. This signal is
not affected by the Mute switch. When depressed, the signal
level can be seen on the Solo meters (which brighten in inten-
sity), and can be heard via the mixer’s headphone or local
monitor output. When this PFL switch is depressed, the associ-
ated yellow LED illuminates.
5-Segment LED Array
The signal is monitored pre-fader. Signal Present LED (green)
responds to levels as low as -30 dB and comes to full bright-
ness at -8dB, varying in intensity according to level. -6dB LED
(green), 0dB LED (green), and +8 dB (yellow) illuminate
accordingly. The Peak (red) LED responds to overloads at
three points in the module; pre-EQ, post-EQ, and post-fader.
100mm Fader
Used for control of all outputs of the channel except those Aux
output sections selected by the PRE/POST switch to a pre-
fader position. (The Insert output level is not affected by the
fader position.)
Scene Mute Assignment Buttons
Assigns input channels to any of the four Scene Mute groups.
Scene Mute combines with the module’s local Mute button,
and actuates the local Mute LED.
Scene Mute Safe Switch
Disables any selected Scene Mute assignments. An associated
green LED indicates the channel is in a Safe state.