Filter
Top Products
e-STUDIO281c/351c/451c ERROR CODE AND SELF-DIAGNOSTIC MODE© June 2005 TOSHIBA TEC
2 - 40
Procedure 6
*When the automatic adjustment ends abnormally, an error message is
displayed.
*Return to standby screen by pressing the [CANCEL] or [CLEAR]
button.
Procedure 7
*When the automatic adjustment ends abnormally, an error message is
displayed.
*Return to standby screen by pressing the [CANCEL] or [CLEAR] button.
Procedure 10
Procedure 14
Note: Note:
The fuser roller temperature control at the adjustment mode is different from that at the normal
state.
Therefore, the problem of fusing efficiency may be occurred in the test copy at the adjustment
mode.
In that case, turn ON the power normally, leave the equipment for approx. 3 minutes after it has
become ready state and then start up the adjustment mode again.
ÅðÃÅëÃ
ÅÐÑÉÛÎÃ
ÅÐÑÉÛÎÃÑÚÚñÑÒ
øÛ¨·¬÷
ÅÜ·¹·¬¿´ µ»§Ã
øݱ¼»÷
ÅÍÌßÎÌÃ
ÅÚßÈà ÅÝÑÐÇÃ÷
øÌ»-¬ ½±°§÷
öÅÝßÒÝÛÔà ±® ÅÝÔÛßÎÃ
ß«¬±³¿¬·½
¿¼¶«-¬³»²¬
ÅðÃÅëÃ
ÅÐÑÉÛÎÃ
ÅÐÑÉÛÎÃ
ÑÚÚñÑÒ
øÛ¨·¬÷
ÅÜ·¹·¬¿´ µ»§Ã
øݱ¼»÷
ÅÍÌßÎÌÃ
ß«¬±³¿¬·½
¿¼¶«-¬³»²¬
ÅÚßÈÃ
ÅÍÌßÎÌÃ
øÌ»-¬ ½±°§÷
öÅÝßÒÝÛÔà ±® ÅÝÔÛßÎÃ
ÅÝßÒÝÛÔÃ
ÅÛÒÌÛÎÃ
ͬ±®»- ª¿´«»
·² ÎßÓ
ÅðÃÅëÃ
ÅÐÑÉÛÎÃ
ÅÐÑÉÛÎÃ
ÑÚÚñÑÒ
øÛ¨·¬÷
ÅÜ·¹·¬¿´ µ»§Ã
øݱ¼»÷
ÅÜ·¹·¬¿´ µ»§Ã
øÍ«¾ ½±¼»÷
ÅÍÌßÎÌÃÅÍÌßÎÌÃÅÍÌßÎÌÃ
ÅÛÒÌÛÎà ±® Å×ÒÌÛÎÎËÐÌÃ
øÊ¿´«» «²½¸¿²¹»¿¾´»÷
Ê¿´«»
¼·-°´¿§»¼
ÅðÃÅëÃ
ÅÐÑÉÛÎÃ
ÅÐÑÉÛÎÃ
ÑÚÚñÑÒ
øÛ¨·¬÷
ÅÜ·¹·¬¿´ µ»§Ã
øݱ¼»÷
ÅÍÌßÎÌÃ
ÅÍÌßÎÌÃ
ÅÜ·¹·¬¿´ µ»§Ã
øÍ«¾ ½±¼»÷
ÅÝßÒÝÛÔÃ
øݱ®®»½¬- ª¿´«»÷
ÅÝÔÛßÎÃ
øݱ®®»½¬- ª¿´«»÷
ÅÛÒÌÛÎÃ
±®
Å×ÒÌÛÎÎËÐÌÃ
ÅÚßÈÃ
ÅÍÌßÎÌÃ
øÌ»-¬ ½±°§÷
ÅËÐÃ ±® ÅÜÑÉÒÃ
øß¼¶«-¬ ¿ ª¿´«»÷
ͬ±®»- ª¿´«»
·² ÎßÓ