Filter
Top Products
EPSON AcuLaser C1100 Revision B
PRODUCT DESCRIPTION Control Panel 51
USB Menu
Note *1: After this item is changed, the setting value takes effect after a warm boot or after the
power is turned on again.
While it is reflected in the Status Sheet and EJL read-back, the actual change takes
effect after a warm boot or after the power is turned on again.
*2: Displayed only when the D4 support USB external device is connected. Changed to
“USB Config=No” automatically when the panel setting mode is finished.
*3: Displayed only when the D4 support USB external device is connected, and “USB
external device=Yes”.
Content of the setting depends on the USB external device settings.
*4: The actual valid value is displayed (but cannot be changed) when “Get IPAddress =
Auto”.
*5: When “Panel” or “PING” is changed to “Auto” in the IP adress setting, the printer
stores the previous setting value, which had been set in the “Panel” or “PING”. The
stored value will be displayed when returning to “Panel” or “PING”.
The printer displays “192.168.192.168” if the settings are not made from the panel.
*6: This item exists as the parameter, but not displayed on the panel.
Network Menu
Note *1: Displayed when a network interface board is installed.
After this item is changed, the setting value takes effect after a warm boot or after the
power is turned on again.
While it is reflected in the Status Sheet and EJL read-back, the actual change takes
effect after a warm boot or after the power is turned on again.
*2: Displayed only when a network interface board is installed. Changed to “Network
Config=No” automatically when the panel setting mode is finished.
*3: Displayed only when a network interface board is installed, and “Network
Config=Yes”.
*4: The default value depends on the controller configuration settings.
*5: The actual valid value is displayed (but cannot be changed) when “Get IPAddress =
Auto”.
*6: This item exists as the parameter, but not displayed on the panel.
*7: When “Panel” or “PING” is changed to “Auto” in the IP adress setting, the printer
stores the previous setting value, which had been set in the “Panel” or “PING”. The
stored value will be displayed when returning to “Panel” or “PING”.
The printer displays “192.168.192.168” if the settings are not made from the panel.
Setting Value Status sheet
USB I/F*
1
On, Off {
USB SPEED*
1
HS, FS {
USB ExtI/Fconfg*
2
No, Yes ---
Get IPAddress*
3
Panel, Auto, PING ---
IP*
3
*
4
*
5
0.0.0.0 to 255.255.255.255 ---
SM*
3
0.0.0.0 to 255.255.255.255 ---
GW*
3
0.0.0.0 to 255.255.255.255 ---
NetWare*
3
On, Off ---
AppleTalk*
3
On, Off ---
MS Network*
3
On, Off ---
Rendezvous*
3
On, Off ---
USB Ext I/F Init*
3
--- ---
Buffer Size*
6
Normal, Maximum, Minimum ---
Setting Value Status sheet
Network I/F*
1
On, Off {
Network Config*
2
No, Yes ---
Get IPAddress*
3
*
4
*
7
Panel, Auto, PING {
IP*
3
*
5
0.0.0.0 to 192.168.192.168 to 255.255.255.255 {
SM*
3
0.0.0.0 to 255.255.255.0 to 255.255.255.255 {
GW*
3
0.0.0.0 to 255.255.255.255 {
AppleTalk*
3
On, Off {
MS Network*
3
On, Off {
Rendezvous*
3
*
4
On, Off {
Link Speed*
3
Auto, 100 Full, 100 Half, 10 Full, 10 Half {
Buffer Size*
6
Normal, Maximum, Minimum ---