Filter
Top Products
Troubleshooting_79
Not Assigned The speed button or
speed dial number
you tried to use has
no number assigned
to it.
Enter the number
manually using the
number keypad or store
the number or address.
Not Available
Try Again Later
Can not perform the
task immediately
because too many
tasks are running at
once.
Try again when current
task is completed.
NonSAMSUNG
Toner
T
The color toner
cartridge which the
arrow indicates is not
a Muratec-genuine
cartridge.
Press OK to toggle
the message to Stop
or Continue.
W Stop X
You can select either
Stop or Continue with
the left/right arrow.
If you select Stop by
pressing OK on the
control panel, the
machine stops printing.
If you select Continue,
the machine keeps
printing, but the quality
cannot be guaranteed.
If you do not select any,
the machine will work as
Stop is selected.
Replace the
corresponding toner
cartridge with a
Samsung-genuine
cartridge. See page 65.
One Page is
Too Large
Single page data
exceeds the
configured mail size.
Reduce the resolution
and try again.
Operation
Not Assigned
You are in the Add
Page/Cancel Job
operation, but there
are no jobs stored.
Check the display to see
if there are any
scheduled jobs.
Out-Bin Full The output tray of the
machine is full of
paper.
Remove paper.
Paper Jam 0
Open/Close Door
Paper has jammed in
the feeding area of the
tray.
Clear the jam. See page
72.
Paper Jam 1
Open/Close Door
Paper has jammed
inside the machine.
Clear the jam. See page
74.
Paper Jam 2
Check Inside
Special print media
has jammed in the
paper exit area.
Clear the jam. See page
75.
Power Failure Power has turned off
then on and the
machine’s memory
has not been back up.
The job which you were
trying to do before the
power failure must be
completely re-done.
Remove Paper
in Rear Cover
Paper has jammed in
the paper rear cover
area.
Clear the jam. See page
75.
MESSAGE MEANING
SUGGESTED
SOLUTIONS
Refilled Toner
T
The toner cartridge
you have installed is
not genuine or refilled.
The print quality may get
poor if the refilled toner
cartridge is installed,
since its characteristics
may significantly differ
from the genuine.
We recommend Muratec
-genuine color
toner cartridge.
Replace Toner
T
This message
appears between
Toner Empty and
Toner Low status.
Replace the toner
cartridge with a new one.
See page 65.
Replace
[xxx]
The life of the part
expires totally.
Replace the part with a
new one. Call for
service.
Replace
[xxx] Soon
The life of the part
expires soon.
See page 68 and call for
service.
Retry Redial? The machine is
waiting for a specified
time interval to redial
a previously busy
station.
You can press OK to
immediately redial, or
Stop/Clear to cancel the
redial operation.
Reverse Jam 0
Check Inside
Paper has jammed in
the paper fuser area
and In the cover of
reverse unit area.
Clear the jam. See page
75.
Reverse Jam 1
Check Inside
Paper has jammed In
the cover of reverse
unit area or in the rear
cover.
Clear the jam. See page
74.
Scanner locked The scanner module
is locked
Unlock the scanner and
press Stop/Clear.
Self Diagnostics
Temperature
The engine in your
machine is checking
problems detected.
Wait a few minutes.
Self Diagnostics
LSU
The LSU (Laser
Scanning Unit) in your
machine is checking
problems detected.
Wait a few minutes.
Send Error
(AUTH)
There is a problem in
SMTP authentication.
Configure the
authentication setting.
Send Error
(DNS)
There is a problem in
DNS.
Configure the DNS
setting.
Send Error
(POP3)
There is a problem in
POP3.
Configure the POP3
setting.
Send Error
(SMTP)
There is a problem in
SMTP.
Change to the available
server.
MESSAGE MEANING
SUGGESTED
SOLUTIONS