Filter
Top Products
En-33
Troubleshooting
If you experience any problem while using the
ABX-N300, look for a solution in this section.
Can’t turn on the ABX-N300.
• Make sure that the AC adapter is properly plugged
into the wall outlet, and that the DC IN connection has
been made correctly (see page 13).
• Unplug the AC adapter from the wall outlet, wait ten
seconds or more, then plug it in again.
The ABX-N300 turns off unexpectedly.
• If the sleep timer has been set and the SLEEP
indication is shown on the display, the ABX-N300
will turn off automatically after a specified period
(see page 25).
• When timed playback finishes, the ABX-N300
automatically switches to standby mode
(see page 24).
It takes a long time from power-on until
operation begins.
• It will take some time for functions related to the
network or to your iPod/iPhone to begin operating.
• If you set “Standby Mode” (see page 30) to
“Network,” the power consumption while in standby
mode will increase, but operation will begin
immediately when you turn the power on.
There’s no sound.
• Make sure the ABX-N300’s volume is not set too low
(see page 14).
• Make sure the correct input source is selected
(see page 14).
• Make sure the ABX-N300 is not muted (see page 14).
• Check all connections and correct as necessary
(see page 13).
The sound quality is not good.
• The sound quality can be affected by strong magnetic
fields, such as that from a TV. Try moving any such
devices away from the ABX-N300.
• If you have any devices that emit high-intensity radio
waves near the ABX-N300, such as a cellular phone
that’s being used to make a call, the ABX-N300 may
output noise.
Low range sounds are inaudible.
• Adjust the tone to your taste or according to the audio
source by activating S.Bass (see page 15).
• Allow a space of 20 cm or more on each side of the
unit (see page 11).
There’s no sound.
• Make sure that your iPod/iPhone is playing.
• Make sure your iPod/iPhone is properly seated in the
ABX-N300’s iPod dock. (see pages 9 and 16).
• Disconnect your iPod/iPhone from the dock, and then
firmly insert it back into the dock.
• Make sure the ABX-N300 is turned on, the input
source is set to iPod, and the volume is not set too low.
• If your iPod or iPhone is in a case, remove the case
before inserting the iPod or iPhone (see page 9).
Can’t control your iPod with the
ABX-N300’s remote controller.
• Make sure your iPod/iPhone is properly seated in the
ABX-N300’s iPod dock. Even very thin iPod/iPhone
cases can prevent the iPod/iPhone from seating
properly on the dock connector, so always remove any
case before inserting your iPod/iPhone
(see pages 9 and 16).
• Disconnect your iPod/iPhone from the dock, and then
firmly insert it back into the dock.
• Depending on your iPod/iPhone model, its software
version, or the content your playing, some functions
may not work as expected (see pages 9 and 16).
Power
If a problem occurs with the ABX-N300’s operation, you
may be able to solve the problem by resetting the unit.
Before you request service, please reset the
ABX-N300 as described below.
1. While the ABX-N300 is in standby mode, press
the remote controller’s [MENU] button.
2. Use the []/[] buttons to select “Reset,” and
press the [ENTER] button.
The screen will indicate “Cancel.”
3. If you decide not to reset, press the [ENTER]
button.
4. To reset, use the []/[] buttons to select
“Settings,” and press the [ENTER] button.
All settings other than the network settings will
return to their factory-set state, and the
ABX-N300 will enter standby mode.
Note:
Selecting “Network” and then pressing the
[ENTER] button will reset network-related
functions. Perform this reset operation ONLY
when the unit’s network or iPod/iPhone does not
function properly.
Audio
iPod/iPhone