Filter
Top Products
EDIT DATA DUMPING TO/LOADING FROM AN EXTERNAL DEVICE
54
The edit data entered in the EDL memory can be transmitted to an external source via the RS-232C connector. For instance,
operation and control can be exercised in a wide range of systems as shown below by uploading data to a computer or down-
loading data from a computer.
1) Off-line editing is possible, and edit data can be used by an on-line system.
2) Edit data can be stored on a hard disk or floppy disk.
3) The edit data can be checked on the computer CRT screen or in printout form.
<Note>
EDL dumping and loading operations cannot be performed while the CONTROL switch is at the REMOTE or EXT VTR setting.
Steps taken for dumping
! Set up the computer or other external unit to receive the data.
@ Press the DUMP (SHIFT + A1) button. The A1 button lamp now flashes, and the event number sent is displayed in the
counter area. The format set in the EDL FORMAT set-up item is selected as the output format.
# The operation is completed when all the edit data in the EDL memory has been transferred. To stop the transfer at any time,
press the ALL STOP button.
Steps taken for loading
! Press the LOAD (SHIFT + A2) button. The A2 button lamp now flashes.
@ The data is sent from the computer or other external unit. The format in which the data is sent must be the format which was
set for set-up menu item No.208 (EDL FORMAT). The event number being received is displayed in the counter area.
# The operation is completed when the computer stops transmitting the data or when the EDL memory is full. To stop the
transfer at any time, press the ALL STOP button.
<Notes>
1. External device settings are required for dumping or loading data.
2. Unless the data is either the corrected or edited EDL data or in a format which is supported by this unit, not only will it be
impossible for the data to be received but the unit may malfunction as well. For this reason, users without a detailed knowl-
edge of personal computers or EDL data should refrain from conducting these operations.
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
VTR1
POWER
REC
CH1
RESET
REC
DIAG
REMOTE
EXT VTR
LOCAL-
VTR1 VTR2
CONTROL
ON
OFF
REC
INHIBIT
OFF
ON
CH2
PB
AUDIO LEVEL
REW
FF
STOP
STB OFF
TRACK
PLAY STILL
1ST EDIT
BS
EVENT
SPLIT
ASMBL
IN OUT
VTR1VTR2 VTR1 VTR2
PREROLL
SYNCHRO
7
5
3
CF
ON
OFF
CH1
MIX
CH2
V1
V1•2
V2
SWAP
NORM
MIX
AUDIO
MONITOR
SPEAKER/
HEADPHONES
AUDIO
SWAP
DUMP LOAD
EDL
CLEAR
FS
RECALL
LAST
EDIT
VA1A2TC
PLAY
IN OUT
GO TO
ENTRY / SHIFT
EDIT MODE
COUNTER
CTL
TC
UB
VTR1
VTR2
RESET
REC
STORE
STOP
STB OFF
MENU
EDIT
STILL
REW
FF
VTR2
REC
CH1 CH2
OPERATION MODE
VTR2 AUDIO
INPUT SELECT
EDIT
INT
EXT
SEPARATE
CH1 CH2
VTR1
EXT
PB
AUDIO LEVEL
PREVIEW
REVIEW MULTI
AUTO
EDIT
ALL STOP
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
VTR1
POWER
REC
CH1
RESET
REC
DIAG
REMOTE
EXT VTR
LOCAL-
VTR1 VTR2
CONTROL
ON
OFF
REC
INHIBIT
OFF
ON
CH2
PB
AUDIO LEVEL
REW
FF
STOP
STB OFF
TRACK
PLAY STILL
1ST EDIT
BS
EVENT
SPLIT
ASMBL
IN OUT
VTR1VTR2 VTR1 VTR2
PREROLL
SYNCHRO
7
5
3
CF
ON
OFF
CH1
MIX
CH2
V1
V1•2
V2
SWAP
NORM
MIX
AUDIO
MONITOR
SPEAKER/
HEADPHONES
AUDIO
SWAP
DUMP LOAD
EDL
CLEAR
FS
RECALL
LAST
EDIT
VA1A2TC
PLAY
IN OUT
GO TO
ENTRY / SHIFT
EDIT MODE
COUNTER
CTL
TC
UB
VTR1
VTR2
RESET
REC
STORE
STOP
STB OFF
MENU
EDIT
STILL
REW
FF
VTR2
REC
CH1 CH2
OPERATION MODE
VTR2 AUDIO
INPUT SELECT
EDIT
INT
EXT
SEPARATE
CH1 CH2
VTR1
EXT
PB
AUDIO LEVEL
PREVIEW
REVIEW MULTI
AUTO
EDIT
ALL STOP
DUMP
LOAD
Computer
Store
Use
Hard disk or
floppy disk
RS-232C
AJ-LT85