Patton electronic 2701RC Network Card User Manual


 
4
cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the fol-
lowing measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected
1.3 CE NOTICE
The CE symbol on your Patton Electronics equipment indicates
that it is in compliance with the Electromagnetic Compatibility (EMC)
directive of the European Union (EU). A Certificate of Compliance is
available by contacting Patton Electronics Technical Support.
1.4 SERVICE INFORMATION
All warranty and non-warranty repairs must be returned freight
prepaid and insured to Patton Electronics. All returns must have a
Return Materials Authorization number on the outside of the shipping
container. This number may be obtained from Patton Electronics
Technical Support at:
tel: (301) 975-1007
email: support@patton.com
www: http://www.patton.com
NOTE: Packages received without an RMA number will not be
accepted.
Patton Electronics’ technical staff is also available to answer any
questions that might arise concerning the installation or use of your
Patton Model 2701RC. Technical Services hours: 8AM to 5PM EST,
Monday through Friday.
2.0 GENERAL INFORMATION
Thank you for your purchase of this Patton Electronics product.
This product has been thoroughly inspected and tested and is warrant-
ed for One Year parts and labor. If any questions arise during installa-
tion or use of the unit, contact Patton Electronics Technical Services at
(301) 975-1007.
2.1 FEATURES
• Terminates E1/FE1 Circuits over a 4-Wire RJ-48C interface
• Connects to standard CPE Serial Interfaces
• Common Framed nx64 rates up to1984 kbps(G.704)
• Unstructured Rate of 2.048 Mbps(G.703)
• G.703 or G.704 Framing (with or without CRC-4, CAS multi-
frame)
• Selectable AMI or HDB3 Line Coding
• Configuration via Internal DIP Switches, software control port, or
SNMP management of local unit through the 1001MC
• Six Easy-to-Read LED Indicators Monitor Data & Diagnostics
• Internal, external, Network Clocking
• Also Operates as a High-Speed Point-to-Point Modem
• Fits into Patton’s 2U Rack-Mount Chassis
• Made in USA
• Conforms to ONP requirements CTR12 and CTR13 for connec-
tion to international telecom networks
2.2 GENERAL PRODUCT DESCRIPTION
The Model 2701RC Series are single port E1/FE1 CSU/DSUs that
provide high-speed WAN connectivity in a rack card package.
Connecting to the serial WAN port of a switch, router or multiplexer, the
NetLink-E1™ provides E1 or FE1 access connection at data rates of
2.048 Mbps and nx64. The Netlink-E1™ is an excellent choice when
terminating leased line services, Frame Relay backbones, internet
access as well as LAN-to-LAN services.
The Netlink-E1™ provides digital access to local WAN services
between two facilities over a dedicated 4-Wire circuit. WAN band-
width, framing and coding options are programmed via internally
accessible DIP switches, via a VT-100 type terminal using a Model
1001CC control card, or SNMP managable through the 1001MC. With
a 1001CC card, a terminal can manage addressable 2701RC cards
using menu driven controls. The Netlink-E1™ uses AMI and HDB3 line
coding. Netlink-E1™ also supports a full range of system and diagnos-
tic features that make system setup easy.
The NetLink-E1™ provides E1 terminations over a modular RJ-48C
jack or dual 75 Ohm BNC connectors when using the 1001RCM11575.
Power options include a single AC or DC or redundant AC/DC.
3