( 52 / 80 )
5.1 Specifications
Table 5.1 Specifications of the M3062PT-EPB
PC7501
M16C/62 Group M16C/62P
M30627FHPGP (two pieces)
ROM: 384 KB + 4 KB, RAM: 31 KB
Single-chip mode
Memory expansion mode (NORMAL, 4 MB)
Microprocessor mode (NORMAL, 4 MB)
(1) 384 KB + 4 KB for internal ROM of MCU
(0F000h--0FFFFh, A0000h--FFFFFh, maximum operating
frequency: 24 MHz, 0 wait)
* When "Disable the Internal Flash ROM" is checked in the
MCU tab of the emulator debugger's MCU Setting dialog box,
it is 10 MHz, 0 wait.
(2) 31 KB for internal RAM
(00400h--07FFFh, maximum operating frequency: 24 MHz, 0
wait)
(3) CS3*--CS0* area
(Possible to allocate by 4 KB, maximum operating frequency: 10
MHz, 0 wait)
24 MHz (Operating voltage: 3.0 to 5.5 V) (When using PLL)
10 MHz (Operating voltage: 2.7 to 3.0 V)
XIN-XOUT (1 to 16 MHz):
Internal oscillator circuit board (OSC-3)
Switchable to external oscillator input or internal generator circuit
X
CIN-XCOUT (32.768 kHz):
Internal oscillator circuit board
Switchable to external oscillator input
Vcc1 = Vcc2: 2.7 to 5.5 V
Vcc1 > Vcc2: 4.8 V ≤ Vcc1 ≤ 5.2 V, 2.7 V ≤ Vcc2 < Vcc1
5 to 35°C (no dew)
-10 to 60°C (no dew)
Supplied from DC power supply of the emulator main unit
For 80-pin 0.65-mm-pitch QFP (80P6S-A):
M3062PT-80FPB (not included)
For 100-pin LCC socket:
M30800T-PTC (included) + IC61-1004-051 (included)
For 100-pin 0.65-mm-pitch QFP (100P6S-A):
(1) M30800T-PTC (included) + M3T-100LCC-DMS (not included)
+ M3T-DIRECT100S (not included)
(2) M30800T-PTC (included) + M3T-100LCC-DMS (not included)
+ M3T-DUMMY100S (not included)
(3) M30800T-PTC (included) + M3T-100LCC-DMS (not included)
+ M3T-FLX-100NRB (not included)
For 100-pin 0.5-mm-pitch LQFP (100P6Q-A):
(1) M3T-F160-100NSD (not included)
(2) M30800T-PTC (included) + M3T-100LCC-QSD (not included)
(3) M30800T-PTC (included) + M3T-100LCC-DMS (not included)
+ M3T-FLX-100NSD (not included)
For 128-pin 0.5-mm-pitch LQFP (128P6Q-A):
M3T-FLX-128NRD (not included)
Emulator
Applicable MCU
Evaluation MCU
Usable MCU mode
Emulation memory
Maximum operating frequency
Clock oscillator
Operating frequency
Operating temperature
Storage temperature
Power supply to emulator
Connection to target system
(see 3.6 "Connecting the Target
System" on page 34)