Filter
Top Products
1-6
VPL-CS2/CX1
GB
10
Location and Function of Controls
qh
qhqh
qh RELEASE (adjuster adjustment)
button
For details, see “How to use the
adjuster” on page 10.
qj
qjqj
qj Connector panel
For details, see “Connector Panel” on
page 12.
qk
qkqk
qk Security lock
Connects to an optional security cable
(Kensington’s).
ql
qlql
ql Ventilation holes (intake)
How to use the adjuster
To adjust the height
Adjust the height of the projector as follows:
1
Lift the projector and press the
RELEASE button.
The adjuster will extend from the
projector.
2
While pressing the button, lower the
projector. Then, release the button.
The adjuster can be set at 6 positions.
• Be careful not to let the projector down on
your fingers.
• Do not push hard on the top of the
projector with the adjuster out.
The security lock corresponds to
Kensington’s MicroSaver Security
System.
If you have any comment, contact:
Kensington
2853 Campus Drive
San Mates, CA 94403
U.S.A.
Tel: 800-535-4242: extension
3348
Home page address:
http://www.kensington.com/
Notes
RELEASE button
11
GB
Location and Function of Controls
Overview
1 I / 1
11
1 (on/standby) key
Turns on and off the projector when the
projector is in standby mode. The ON/
STANDBY indicator lights in green
when the power is turned on.
When turning off the power, press
the I / 1 key twice following the
message on the screen, or press and hold
the key for about one second.
For details on steps for turning off the
power, see “To turn off the power” on
page 24.
2 INPUT key
Selects the input signal. Each time you
press the key, the input signal switches
as follows:
3 APA (Auto Pixel Alignment) key
Adjusts a picture clearest automatically
while a signal is input from a computer.
4 VOLUME +/– keys
Adjust the volume of the built-in
speakers.
+ : Increases the volume.
–
:
Decreases the volume.
5 Indicators
• LAMP/COVER: Lights up or flashes
under the following conditions:
– Lights up when the lamp has
reached the end of its life or
becomes a high temperature.
– Flashes when the lamp cover or air
filter cover is not secured firmly.
• FAN/TEMP (Temperature): Lights
up or flashes under the following
conditions:
– Lights up when temperature inside
the projector becomes unusually
high.
– Flashes when the fan is broken.
• POWER SAVING: Lights up when
the projector is in power saving mode.
When POWER SAVING in the SET
SETTING menu is set to ON, the
projector goes into power saving mode
if no signal is input for 10 minutes.
Although the lamp goes out, the
cooling fan keeps running. In power
saving mode, any key does not
function for the first 30 seconds. The
power saving mode is canceled when a
signal is input or any key is pressed.
• ON/STANDBY: Lights up or flashes
under the following conditions:
– Lights in red when a AC power cord
is plugged into a wall outlet. Once in
standby mode, you can turn on the
projector with the I / 1 key.
– Lights in green when the power is
turned on.
– Flashes in green while the cooling
fan runs after the power is turned off
with the I / 1 key. The fan runs for
about 90 seconds after the power is
turned off.
The ON/STANDBY indicator
flashes quickly for the first 30
seconds. During this time, you
cannot light up the ON/STANDBY
indicator with the I / 1 key.
For details on the LAMP/COVER and
the FAN/TEMP indicators, see on page
35.
Control Panel
RESET MENU
POWER
INPUT
APA
VOLUME
POWER SAVING
ON/STANDBY
FAN/TEMP
LAMP/COVER
ENTER
+
–
INPUT A
t
VIDEO
t
S VIDEO
t