Filter
Top Products
1-14
VPL-CS2/CX1
GB
26
Using the MENU
”
Adjustments and Settings Using the Menu
Using the MENU
The projector is equipped with an on-screen
menu for making various adjustments and
settings. You can change the menu language
displayed in the on-screen menu.
To change the menu language, see
“Selecting the Menu Language” on page 20.
1
Press the MENU key.
The menu appears.
The menu presently selected is shown as
a yellow button.
2
Use the >. or key to select a menu,
then press the
/
>.
/
or ENTER key.
The selected menu appears.
3 Select an item.
Use the or key to select the item,
then press the or ENTER key.
4 Make the setting or adjustment on an
item.
. When changing the adjustment level:
To increase the number, press the or
key.
To decrease the number, press the
or key.
Press the ENTER key to restore the
original screen.
. When changing the setting:
Press the > or .
key to change the
setting.
Press the ENTER or key to restore
the original screen.
To clear the menu
Press the MENU key.
The menu disappears automatically if a key
is not pressed for one minute.
To reset items that have been
adjusted
Press the RESET key.
“Complete!” appears on the screen and the
settings appearing on the screen are reset to
their factory preset values.
Items that can be reset are:
. “CONTRAST,” “BRIGHT,” “COLOR,”
“HUE,” and “SHARP” in the PICTURE
CTRL menu
. “DOT PHASE,” “SIZE,” and “SHIFT” in
the INPUT SETTING menu
. “DIGITAL KEYSTONE” in the SET
SETTING menu
About the memory of the settings
The settings are automatically stored in the
projector memory.
If no signal is input
If there is no input signal, “NO INPUT–
Cannot adjust this item.” appears on the
screen.
80
50
PICTURE CTRL
CONTRAST:
BRIGHT:
GAMMA MODE: GRAPHICS
COLOR TEMP: HIGH
INPUT-A
SET SETTING
STATUS: ON
INPUT-A: RGB
KEYSTONE MEMORY:
OFF
DIGITAL KEYSTONE:
OFF
LANGUAGE: ENGLISH
POWER SAVING
: OFF
SIRCS RECEIVER:
FRONT&REAR
LAMP TIMER: 000
10h
INPUT-A
Menus
Setting items
>
/
.
?
?
27
GB
The PICTURE CTRL Menu
Adjustments and Settings Using the Menu
The PICTURE CTRL
Menu
The PICTURE CTRL (control) menu is used
for adjusting the picture.
Items that cannot be adjusted depending on
the input signal are not displayed in the
menu.
For details on the unadjustable items, see
page 40.
When the video signal is input
When the RGB signal is input
CONTRAST
Adjusts the picture contrast. The higher the
setting, the greater the contrast. The lower
the setting, the lower the contrast.
BRIGHT
Adjusts the picture brightness. The higher
the setting, the brighter the picture. The
lower the setting, the darker the picture.
COLOR
Adjusts color intensity. The higher the
setting, the greater the intensity. The lower
the setting, the lower the intensity.
HUE
Adjusts color tones. The higher the setting,
the picture becomes greenish. The lower the
setting, the picture becomes purplish.
SHARP
Adjusts the picture sharpness. The higher the
setting, the sharper the picture. The lower
the setting, the softer the picture.
D. (Dynamic) PICTURE
Emphasizes the black color.
ON: Emphasizes the black color to produce
a bolder “dynamic” picture.
OFF: Reproduces the dark portions of the
picture accurately, in accordance with
the source signal.
GAMMA MODE
Selects a gamma correction curve.
GRAPHICS: Improves the reproduction of
halftones. Photos can be reproduced in
natural tones.
TEXT: Contrasts black and white. Suitable
for images that contain lots of text.
COLOR TEMP
Adjusts the color temperature.
HIGH: Makes the white color bluish.
LOW: Makes the white color reddish.
COLOR SYS (System)
Selects the color system of the input signal.
.AUTO: NTSC
3.58
, PAL, SECAM and
NTSC
4.43
(switched automatically)
.PAL-M/N: PAL-M/PAL-N and NTSC
3.58
(switched automatically)
Normally, set to AUTO. If the picture is
distorted or colorless, select the color system
according to the input signal.
Menu Items
PICTURE CTRL
CONTRAST:
BRIGHT:
COLOR:
HUE:
SHARP:
D. PICTURE:
COLOR TEMP:
COLOR SYS:
VIDEO
80
50
50
50
50
OFF
LOW
AUTO
80
50
PICTURE CTRL
CONTRAST:
BRIGHT:
GAMMA MODE: GRAPHICS
COLOR TEMP: HIGH
INPUT-A