Filter
Top Products
55
Ch. 3 Functions
Functions
To change the setting for the Size function:
1 Select GLOBAL FORMAT, BLOCK FOR-
MAT or LINE FORMAT (OR hold down
d and press 1, 2 or 3) as described
on pages 52 to 53.
2 Rotate r until SIZE is displayed, and then
press r (OR press j or k until SIZE is
displayed). The setting for the text at the
cursor’s current position is shown on the
left side of the display and a sample can be
seen on the right side.
3 Rotate r (OR press m or g) until the
desired setting is displayed.
4 Press r (OR press n) to apply the setting.
Width function (WIDTH)
The Width function can be used with any of the
text sizes to make the size of the characters
wider or more narrow. For samples of the avail-
able Width settings, refer to page 100. The
width of the text at the cursor’s current position
is shown at the bottom of the display.
To change the setting for the Width func-
tion:
1 Select GLOBAL FORMAT, BLOCK FOR-
MAT or LINE FORMAT (OR hold down
d and press 1, 2 or 3) as described
on pages 52 to 53.
NOTE
☞
Since the text sizes that can be printed depends
on the width of the tape, the following table
shows the maximum text size that can be used
with each tape width.
The following text sizes do not apply to text
with a Text rotation setting applied.
☞
With the AUTO setting selected and the text in
a block consisting of just one line of only upper-
case letters (and no accented letters) and written
horizontally/vertically without the BERMUDA
font, the text is printed slightly larger than the
maximum possible.
☞
If the 4 point or 5 point text size setting is
selected, the text will be printed with the BRUS-
SELS font setting, regardless of the font setting
that is selected.
NOTE
This step may be skipped if settings for several for-
mat functions are being applied at the same time.
Tape width
Maximum text size
(in points)
6 mm 12
9 mm 20
12 mm 28
18 mm 40
24 mm 64
36 mm 76
Length Margin Font Width Size
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
K
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
R
R
R
R
R
R
G
H
I
J
AUTO 0.4 HELSINKI A AUTO
02/13
SIZE
AUTO
L
M
NO
NOTE
☞
If “*****” appears as a setting, the Size function
has already been applied to either a line in the
current text block (if the Block format or the
Global format function is being set) or a block
in the current text (if the Global format function
is being set). Changing the setting will cancel
the setting that was previously applied.
☞
To return the function to its default setting
(AUTO), press the space bar.
☞
To return to the text without changing the for-
matting, press e (OR hold down d and
press 1, 2 or 3).
NOTE
If r is used to select the settings, only one function
can be set at a time. To apply several format set-
tings at the same time, press j or k to select the
function, and then press m or g to select the
desired setting. Press n only after the necessary
functions have been set.
Length Margin Font Width Size
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
K
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
R
R
R
R
R
R
G
H
I
J
L
M
NO
AUTO 0.4 HELSINKI A AUTO
<<< P-touch >>>
1
:
_