Filter
Top Products
I-2 SmartCell 6A000/ZX-250 Reference Manual
Index
C
CACParams switch attribute
..... 2-20
to
2-21
CACStat switch attribute
........... 2-22
to
2-23
cause codes
AAL parameters cannot be
supported
........................................... B-2
Access information discarded
........... B-2
Bearer capability not authorized
....... B-2
Bearer capability not implemented
... B-2
Bearer capability not presently
available
............................................ B-2
Call control block not found
............. B-3
Call rejected
...................................... B-1
Calling party number not set.
............ B-3
Destination out of order
.................... B-1
Identified channel does not exist
...... B-2
Incompatible destination
................... B-2
Incorrect message length
.................. B-2
Information element non-existent
or not implemented
.........................
B-2
Internal resource error
....................... B-3
Invalid call reference value
............... B-2
Invalid endpoint reference
................ B-2
Invalid information element contents
B-2
Invalid number format
...................... B-1
Invalid transit network selection
....... B-2
Link not active
.................................. B-3
Link not found
.................................. B-3
Mandatory information element is
missing
.............................................. B-2
Message not compatible with call
state
................................................... B-2
Message type non-existent or not
implemented
..................................... B-2
Network out of order
........................ B-2
No response from network
................ B-2
No response to connect
..................... B-2
No response to out-going call process
B-2
No response to restart request
........... B-3
No route to destination
...................... B-1
No route to specified transit network
B-1
No user responding
........................... B-1
No VPI/VCI available
....................... B-2
Normal cell clearing
......................... B-1
Normal, unspecified
.......................... B-1
Number changed
............................... B-1
Protocol error, unspecified
................ B-2
Quality of Service unavailable
.......... B-2
Recovery on timer expire
..................B-2
Requested VPI/VCI not available
.....B-1
Resource unavailable, unspecified
....B-2
Response to STATUS ENQUIRY
....B-1
SAP not active
..................................B-3
Service or option not available,
unspecified
........................................B-2
Temporary failure
.............................B-2
Too many pending add party requests
B-2
Unassigned number
...........................B-1
Unsupported combination of traffic
parameters
.........................................B-2
User busy
..........................................B-1
User cell rate not available
................B-1
User cell rate unavailable
..................B-2
User rejects all calls with calling
line identification
..............................B-1
VPI/VCI assignment failure
..............B-1
VPI/VCI pair is unacceptable
...........B-1
CCTm
...................................................2-175
Cell Memory Size
.................................2-185
change default boot load image
................3-3
changing switch start-up behavior
............3-1
changing the boot load default
.................3-1
Chnl DVT
.............................................2-164
chpi
...........................................................3-3
clear
config
...............................................2-39
clear flash file system
...............................3-4
clear switch configuration
........................3-4
clfs
............................................................3-4
Client Address
........................................2-24
Client State
.............................................2-24
Client Type
.............................................2-30
ClientNumber
............2-24
,
2-28
,
2-30
,
2-35
,
.......................... 2-56
,
2-58
,
2-61
,
2-64
,
2-66
command defined
.....................................1-1
Common DRAM
..................................2-185
Community Name
..................................2-37
Config
.....................................................2-39
Configuration Errors
...............................2-79
Configured VCI Bits
............................2-133
Configured VPI Bits
.............................2-133
Conn SubId
............................... 2-149
,
2-177
ConnectionCompeteTime
.......................2-84
ConnectMethod
...................2-13
,
2-41
,
2-94
ConnId
...................................... 2-149
,
2-177
ConnType
................................. 2-148
,
2-178