Filter
Top Products
5-26. The 4U library Monitor Library: Drive
Identity page showing one Fibre Channel
drive (#1) and one SCSI drive (#2) . . . . 5-33
5-27. The 4U library Monitor Library: Library
Status page . . . . . . . . . . . 5-34
5-28. The 4U library Monitor Library: Drive
Status page . . . . . . . . . . . 5-36
5-29. The 2U library Monitor Library: Inventory
page . . . . . . . . . . . . . 5-37
5-30. The 4U library Monitor Library: Inventory
page . . . . . . . . . . . . . 5-38
5-31. The 4U library Configure Library: General
and Extended page . . . . . . . . . 5-40
5-32. The 4U library Configure Library: Logical
Libraries page . . . . . . . . . . 5-40
5-33. The 4U library Configure Library: Path
Failover page . . . . . . . . . . 5-41
5-34. Path Failover license verification page 5-41
5-35. Feature Activation Key screen . . . . . 5-42
5-36. Configure Library: Encryption Feature
configuration screen . . . . . . . . 5-42
5-37. The Configure Library: Drive page for a
4U library . . . . . . . . . . . . 5-44
5-38. Configure Library: Network page 5-45
5-39. Warning screen . . . . . . . . . . 5-45
5-40. Configure Library: User Access page 5-47
5-41. The Configure Library: Date & Time page 5-47
5-42. Configure Library: Logs & Traces page 5-48
5-43. Configure Library: Event Notification page 5-48
5-44. Configure Library: Restore Defaults page 5-49
5-45. Manage Library: Move Media page 5-49
5-46. Manage Library: Perform Inventory page 5-50
5-47. Manage Library: Release Magazine page 5-50
5-48. Service Library: Clean Drive page 5-51
5-49. Service Library: View Logs page 5-51
5-50. Service Library: View Drive Logs screen 5-52
5-51. Service: Save Drive Dump . . . . . . 5-52
5-52. Service Library: Perform Diagnostics page 5-53
5-53. Service Library: Perform Key Path
Diagnostics page . . . . . . . . . 5-53
5-54. The 2U library Service Library: Upgrade
Firmware page . . . . . . . . . . 5-54
5-55. The 4U library Service Library: Upgrade
Firmware page . . . . . . . . . . 5-55
5-56. Service Library: Reboot page . . . . . 5-55
6-1. The LTO Ultrium 800 GB Data Cartridge 6-1
6-2. Ultrium WORM Tape Cartridge . . . . . 6-3
6-3. Sample bar code label on the LTO Ultrium 4
Tape Cartridge . . . . . . . . . . 6-5
6-4. Setting the write-protect switch . . . . . 6-6
6-5. Double-boxing tape cartridges for shipping 6-7
6-6. Checking for gaps in the seams of a
cartridge . . . . . . . . . . . . 6-8
7-1. A 250w power supply with LEDs 7-8
7-2. A 80w power supply without LEDs 7-9
9-1. Access holes for the left magazine 9-2
9-2. Access holes for the right magazine 9-3
9-3. Left Magazines pulled out of the 2U library 9-4
9-4. Left Magazines pulled out of the 4U Library 9-4
10-1. Shipping lock and label storage location 10-2
10-2. Shipping lock and label . . . . . . . 10-2
10-3. Library drive sled without ElectroStatic
Discharge (ESD) springs (SCSI sled shown) 10-3
10-4. Library drive sled with ESD springs [1]
(SAS sled shown) . . . . . . . . . 10-4
10-5. Drive sled components (full-high fibre
drive in top position, half-high SCSI drive
in middle position, half-high SAS drive in
bottom position) on back panel of a 4U
library . . . . . . . . . . . . . 10-4
10-6. Pulling the drive sled out of the library
(drive sled without ESD springs shown) . 10-5
10-7. Pushing the drive sled into the library
(drive sled without ESD springs shown) . 10-6
10-8. Diagrams for applying conductive tape for
ESD protection to the back of a drive sled
installed in a 2U or 4U library . . . . . 10-7
10-9. A power supply being removed from a 2U
library . . . . . . . . . . . . . 10-8
10-10. A Library Controller Card being removed
from the library . . . . . . . . . . 10-9
10-11. Rear panel of a 4U library with a Fibre
Channel full height drive in the top
position, a SCSI half height drive in the
middle position, and a SAS half height
drive in the bottom position . . . . . 10-11
10-12. Removing the two mounting bracket
screws anchoring the library to the rack
(one screw on each side of the library . . 10-11
10-13. Foot pads installed on the bottom of the
library enclosure . . . . . . . . . 10-13
10-14. Removing the shipping label and lock
from the top of the library and storing on
the rear panel . . . . . . . . . . 10-14
10-15. Library shipping lock and label storage
location on the real panel of the library . 10-14
10-16. Removing a Library Controller Card from
the library . . . . . . . . . . . 10-16
10-17. Library Front Panel LEDs . . . . . . 10-17
10-18. Removing a drive sled from the library
(drive sled without ESD springs shown) . 10-18
10-19. Drive sled taping diagrams . . . . . 10-19
10-20. Access hole for the left magazine (facing
rear of library) . . . . . . . . . . 10-20
10-21. Access hole for the right magazine (facing
rear of library) . . . . . . . . . . 10-21
10-22. Left magazine pulled out of a 4U library
(facing front of library) . . . . . . . 10-22
10-23. A power supply being removed from a
library . . . . . . . . . . . . 10-23
10-24. Mounting brackets and anchors for
securing the library in a rack (one bracket
and anchor on each side of the library) . . 10-24
10-25. Front view of a rack showing the rails
installed . . . . . . . . . . . . 10-24
A-1. Configuration of a One Partition System A-3
A-2. Configuration of a Two Partition System A-4
A-3. Configuration of a Three Partition System A-4
A-4. Configuration of a Four Partition System A-5
A-5. Examples of SCSI Element Addressing A-5
viii Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide