Filter
Top Products
52 C1522M-C (2/05)
PRIORITY
The CM6800 provides eight levels of priority control. Each level defines the ability of a keyboard to control a pan/tilt/zoom (camera
positioning system) and to access programming screens.
Priority level applies system wide; a keyboard assigned priority level 2 on COM port 5 has a higher priority than a keyboard assigned priority level
4 on COM port 4. A higher level keyboard takes precedence over a lower level keyboard when the keyboards are issuing control commands.
Figure 42. Access the Priority Screen
PORT: Select the COM port number for which you are programming priority control.
PRIORITY: For each keyboard connected to the specified port, assign a priority level (01-08).
OPTIONS:
Level 1 = highest priority
Level 8 = lowest priority
Levels 1 - 3 have the ability to access programming screens. Levels 4-8 cannot access programming screens. The lowest
level or keyboards located at the same level will access devices on first-come, first-served basis.
NOTE: If you connect an ASCII keyboard/device to the CM6800 (COM port 1, 2, or 4), you can connect only one keyboard to a port. For
ASCII keyboards, priority control is based on the entry for keyboard 1.
SEQUENCE
The CM6800 provides two types of sequences:
• An operator can program a scratchpad sequence from an individual monitor, without accessing password-protected programming
screens.
• System sequences are password-protected and can run on any system monitor.
PELCO SWITCHER
MODEL CM6800
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 ABOUT CM6800
ENGLISH
RETURN
00654
KEYBOARD PRIORITY MENU
PORT 05
KBD PRIORITY
101
202
308
408
508
608
708
808
RETURN
00658
PELCO SWITCHER
MODEL CM6800
MAIN MENU
1 CAMERA
2 LOGICAL CAMERA
3 MONITOR
4 ACCESS
5 TIME & DATE
6 PORT
7 PRIORITY
8 SEQUENCE
9 MACRO
10 ALARM CONTACTS
11 EVENT TIMER
12 SET AUXILIARY
13 SET PASSWORD
14 ABOUT CM6800
ENGLISH
RETURN
00654
SEQUENCE 01 HELP
STP CAM DWL CMD ## AUX ##
01 0001 02
PATT
01 CON 000
02 0002 02 PRES 01 CON 000
03 0003 03 SSCN 00
— — — —
000
04 0004 02 FSCN 00
— — — —
000
05 0005 08 PRES 04 COFF 000
06 0006 02
— — — —
00
— — — —
000
07 0006 02
— — — —
00
— — — —
000
08 0006 02
— — — —
00
— — — —
000
09 0006 02
— — — —
00
— — — —
000
10 0006 02
— — — —
00
— — — —
000
11 0006 02
— — — —
00
— — — —
000
12 0006 02
— — — —
00
— — — —
000
13 0006 02
— — — —
00
— — — —
000
14 0006 02
— — — —
00
— — — —
000
15 0006 02
— — — —
00
— — — —
000
16 0006 02
— — — —
00
— — — —
000
17 0006 02
— — — —
00
— — — —
000
18 0006 02
— — — —
00
— — — —
000
NEXT PREVIOUS
RETURN
00660
Figure 43. Sequence Screen