Filter
Top Products
12-5
Chapter 12: Parameters
12
Parameter address (System memory address)
Parameter
address
(8)
Set value for switch SW3
Details of parameter
(Details --
-
-- See page 12-1)
0 1 2 3 4
00 #0300 #1400 #1500 #1600 #1700 IP address
01 #0301 #1401 #1501 #1601 #1701 IP address
02 #0302 #1402 #1502 #1602 #1702 IP address
03 #0303 #1403 #1503 #1603 #1703 IP address, node number
04 #0304 #1404 #1504 #1604 #1704 Token monitor time (normally set to 10 ms)
05 #0305 #1405 #1505 #1605 #1705 Minimum frame interval (normally set to 0)
06
to
07
#0306
to
#0307
#1406
to
#1407
#1506
to
#1507
#1606
to
#1607
#1706
to
#1707
Reserved area
10 #0310 #1410 #1510 #1610 #1710
Sending area top address of area 1 for
local node (Word address)
11 #0311 #1411 #1511 #1611 #1711
12 #0312 #1412 #1512 #1612 #1712
Sending data length (word) of area 1 for
local node area 1
13 #0313 #1413 #1513 #1613 #1713
14 #0314 #1414 #1514 #1614 #1714
Sending area top address of area 2 for the
local node (Word address)
15 #0315 #1415 #1515 #1615 #1715
16 #0316 #1416 #1516 #1616 #1716
Sending data length (word) of area 2 for
local node
17 #0317 #1417 #1517 #1617 #1717
20 #0320 #1420 #1520 #1620 #1720
Top address (word address) of area 1 on
PC
21 #0321 #1421 #1521 #1621 #1721
22 #0322 #1422 #1522 #1622 #1722 File number of area 1 on PC
23 #0323 #1423 #1523 #1623 #1723 Reserved area
24 #0324 #1424 #1524 #1624 #1724
Top address (word address) of area 2 on
PC
25 #0325 #1425 #1525 #1625 #1725
26 #0326 #1426 #1526 #1626 #1726 File number of area 2 on PC
27 #0327 #1427 #1527 #1627 #1727 Reserved area
30 #0330 #1430 #1530 #1630 #1730
Top address of communication control area
(word address) on PC
31 #0331 #1431 #1531 #1631 #1731
32 #0332 #1432 #1532 #1632 #1732
File number of communication control area
on PC
33 #0333 #1433 #1533 #1633 #1733
Transmission type of communication control
area
33 #0334 #1434 #1534 #1634 #1734
Top address of transmission buffer (word
address)
35 #0335 #1435 #1535 #1635 #1735
36 #0336 #1436 #1536 #1636 #1736 File number of transmission buffer
37 #0337 #1437 #1537 #1637 #1737 Use selection of transmission buffer
40
to
51
#0340
to
#0351
#1440
to
#1451
#1540
to
#1551
#1640
to
#1651
#1740
to
#1751
Node name (ASCII 10 characters)
52
to
57
#0352
to
#0357
#1452
to
#1457
#1552
to
#1557
#1652
to
#1657
#1752
to
#1757
Reserved area
60 #0360 #1460 #1560 #1660 #1760 SEND/RECEIVE instruction timeout time
61
to
76
#0361
to
#0376
#1461
to
#1476
#1561
to
#1576
#1661
to
#1676
#1761
to
#1776
Reserved area
77 #0377 #1477 #1577 #1677 #1777 Start switch
- Parameter addresses on the JW-50FL
Depending on the setting of switch SW3 on the JW-50FL, the addresses of the parameters (in system
memory) will vary, as shown below. In this manual, the parameter addresses in the left column of the
tables are expressed in their common form.