Filter
Top Products
APPENDIX A / ANNEXE A OCTO² / QFX402
PAGE 50
COMMAND RESPONSE COMMAND DESCRIPTION VALUE /VALEUR
COMMANDE RÉPONSE DESCRIPTION DE LA COMMANDE
TYPE
MIN MAX DESCRIPTION
STATUS COMMANDS / COMMANDES D'ÉTAT
UN UN Measures unity in tens of kHz.
Rd
0 65535 ex: 14500 = 145 MHz
IL IL Horizontal period of input signal.
Rd
0 65535
Line frequency (in kHz) = (UN VALUE)x10 ÷
(IL VALUE).
ID ID Vertical period of input signal.
Rd
0 65535 Frame frequency (in Hz) = (Line frequency in
Hz) ÷ (ID VALUE).
IP IP Input Sync. detection.
Rd
0 1 0 = no Sync. detected 1 = Sync. detected.
IH IH Sign of the horizontal input Sync.
Rd
0 1 0 = negative 1 = positive.
IV IV Sign of the vertical input Sync.
Rd
0 1 0 = negative 1 = positive.
IK IK Input Sync type detection.
Rd
0 3 0 = Separate H &V sync.
1 = Composite sync. (TTL).
2 = SOG (Sync. On Green).
3 = Composite sync. (analog).
II II Interlaced signal detection.
Rd
0 1 0 = not interlaced 1 = interlaced.
IO IO "Out of range" signal detection.
Rd
0 1 0 = In range 1 = Out of range.
IF IF Standard input signal detection.
Rd
0 35 0 = no signal 1 = wrong signal
2 = NTSC std (3.58/60) 3 = PAL std (4.43/50)
4 = SECAM (50Hz) 5 = B&W (50Hz)
6 = B&W (60Hz) 7 = YUV 50Hz
8 = YUV 60Hz 9 = RGB 50Hz
10 = RGB 60Hz 11 = 640x480
12 = 800x600 13 = 1024x768
14 = 1280x1024 15 = 1400x1050
16 = 1600x1200 17 = 852x480
18 = 1280x720 19 = 1280x768
20 = 1366x768 21 = 1680x1050
22 = 1920x1080 23 = 1080i 50
24 = 1080i60 25 = 720p 50
26 = 720p 60 26 = 1080p 24
28 = 1080p 25 29 = 1080p 30
30 = 1080p 50 31 = 1080p 60
32 = 1080sf 24 33 = 480p 50
34 = 480p 60 35 = 480p 72
XA XA Synchronized input.
Rd
0 8
Identical as XR command.
XF XF Synchronized input standard.
Rd
0 29
Identical as IF command.
XT REFT Frame frequency of the synchronized
input.
Rd
0 65535 Value in hundredth of Hz.
OTHERS COMMANDS / COMMANDES DIVERSES
TP TP T-BAR position. Rd/Wr 0 255
TB TB Executed percentage of the effect.
Rd
0 65535 0 = 0% 65535 = 100%
? DEV Device type.
Rd
0 65535 44 = OFX803 45 = OFD803
46 = OCP803. 49 = QFX402
# #1,....#0 Send all device parameters.
Rd
NOTE: Rd/Wr = Read and write command / Commande de lecture et d'écriture. Rd = Read only command / Commande de lecture uniquement.