Filter
Top Products
5-2
Connections
5976052 BARCOREALITY 9300 070999
RGB V
RGB
H / C
V
On
98 27910
RGB
H / C
V
H
RS 232 IN
REMOTE
PROJECTOR MODE :
GREEN - OPERATION
RED - STANDBY
COMMUNICAT ION PORT
(800-PERIPHERALS)
RS232 OUT
IR-ACKNOWLEDG E D
IR-RECEIVED
DIAGNOSTICS
CODE IR-RECEIVER
0
I
This device complies with Part 15 of the FCC rules. Operation
is subject to following two conditions :
(1) This device may not cause harmful interference
(2) This device must accept any interference received
including interference that may cause undesired operation
XLRSDI IN SDI O UT
- Reconnect the power cord to the wall outlet and switch on the
projector.
The new installed module can be selected with the digit buttons on
the RCU or the local keypad.
Input Connections.
The projector has three fixed and two modular input
facilities. The modular input slots (slot 3 and 4) can be filled
up with the following modules :
Video, S-video input order no. : R9827900
RGBS/RGsB analog input order no. : R9827910
RGB3S/RG3sB input order no. : R9827920
Component Video order no. : R9827930
The sequence of insertion has no importance. Duplicated
inputs can be used.
Note : When using a RCVDS05 or VS05, the input configu-
ration of the projector must be as follows:
Slot 1 : not used
Slot 2 : RGB and Component video input
Slot 3 : Video input module
Slot 4 : not used
When using a RCVDS05, it is recommended to use a 5-cable
output module in the RCVDS. The outputs of this module has
to be connected to slot 2 of the projector.
To switch the projector in the 5-cable mode see chapter
'Installation mode'.
Input module insertion into the projector :
- Power down the projector and disconnect the power cord
from the wall outlet.
- Remove the dummy plate covering the chosen input slot
by turning out both screws.
- Slide the input module in the free slot. Insure the module
is seated correctly in the guide grooves.
- Press on both handles of the input module until the module
plug seats in the connector of the projector.
- Secure the input module by tightening both retaining
screws.
Switching to Stand-by.
When the projector is running and you want to go to stand-by, press
the stand-by key.
Switching Off
To switch off:
- First press STANDBY key and let the projector cool down until the
fans stop blowing, or at least 15 min.
- Switch off the projector with the power switch.
WARNING : When switching to standby, never restart the
projector (hot restrike) within the first 3 minutes to avoid
damage to the lamp.
Lamp Run Time
When the total run time of the lamp is 970 hours or more, the following warning message
will be displayed for 1 minute. This warning message will be repeated every 30 minutes.
Press EXIT to remove the message before the minute is over.
When the total run time of the lamp is 1000 hours or more, the following warning message,
with the exact run time is displayed on the screen.
Lamp run time is 1000 hours. Operating the lamp longer than 1000 hours may damage
the projector. Please replace the lamp.
When OK (ENTER) is pressed to go on, the warning will be repeated every 30 min.
The total lifetime of the lamp for a safe operation is 1000 hours max. Do not use it longer.
Always replace with a same type of lamp. Call a BARCO authorized service technician
for lamp replacement.
Warning : Using a lamp for more than 1000 hours is dangerous as the
lamp could explode.
Lamp run time
980 h
<ENTER> to continue
WARNING
Lamp run time is 1000 hours
Operating the lamp longer
than 1000 hours may damage
the projector.
Please replace the lamp