Filter
Top Products
Adapter configurations 117
LOAD QASP.LAN VSLOT=4 FRAME=Ethernet_II NAME=QASP_4_EII
LOAD Q57.LAN SLOT=7 speed=100fd FRAME=Ethernet_II NAME=Q57_7_EII
LOAD Q57.LAN SLOT=8 speed=100fd FRAME=Ethernet_II NAME=Q57_8_EII
bind qasp4 q57_7_eii
bind qasp4 q57_8_eii
BIND IP QASP_4_EII ADDR=192.222.23.1 MASK=255.255.255.0
• Example 6: VLAN with QASP
LOAD ODINEB.NLM
LOAD QASP.LAN FRAME=ETHERNET_II NAME=QASP_1_V100_EII VSLOT=1 VLAN=100
LOAD QASP.LAN FRAME=ETHERNET_II NAME=QASP_1_V200_EII VSLOT=1 VLAN=200
LOAD QASP.LAN FRAME=ETHERNET_II NAME=QASP_1_V300_EII VSLOT=1 VLAN=300
LOAD Q57.LAN FRAME=ETHERNET_II NAME=Q57_1_EII SLOT=1 VLAN=1
LOAD Q57.LAN FRAME=ETHERNET_II NAME=Q57_2_EII SLOT=2 VLAN=1
BIND QASP1 Q57_1_EII
BIND QASP1 Q57_2_EII
BIND IP QASP_1_V100_EII ADDR=172.16.210.1 MASK=255.255.0.0
BIND IP QASP_1_V200_EII ADDR=172.17.220.1 MASK=255.255.0.0
BIND IP QASP_1_V300_EII ADDR=172.18.230.1 MASK=255.255.0.0
NOTE: When binding Q57_1_V100_EII to Q57_1_EII, Q57_1_EII is also bound to the other
VLANs on the same VSLOT. VLAN refers to VLAN ID, and a valid VLAN ID ranges from 1 to
4094.
• Example 7: Trunking with QASP
LOAD ODINEB.NLM
LOAD QASP.LAN FRAME=ETHERNET_II NAME=QASP_1_EII VSLOT=1 MODE=TRUNK
LOAD Q57.LAN FRAME=ETHERNET_II NAME=Q57_1_EII SLOT=1
LOAD Q57.LAN FRAME=ETHERNET_II NAME=Q57_1_EII SLOT=2
BIND QASP1 Q57_1_EII
BIND QASP1 Q57_2_EII
BIND IP QASP_1_EII ADDR=172.16.210.1 MASK=255.255.0.0
NOTE: Switch ports must be configured for Trunking (for example, FEC or GEC for Cisco
switches).
• Example 8: GVRP with QASP
LOAD ODINEB.NLM
LOAD QASP.LAN FRAME=ETHERNET_II NAME=QASP_1_EII VSLOT=1 VLAN=100 GVRP
LOAD QASP.LAN FRAME=ETHERNET_802.2 NAME=QASP_1_E82 VSLOT=1
LOAD Q57.LAN FRAME=ETHERNET_II NAME=Q57_1_EII SLOT=1
LOAD Q57.LAN FRAME=ETHERNET_802.2 NAME=Q57_1_E82 SLOT=1
LOAD Q57.LAN FRAME=ETHERNET_II NAME=Q57_2_EII SLOT=2
LOAD Q57.LAN FRAME=ETHERNET_802.2 NAME=Q57_2_E82 SLOT=2
BIND QASP1 Q57_1_EII
BIND QASP1 Q57_2_EII
BIND IP QASP_1_EII ADDR=172.16.210.1 MASK=255.255.0.0
NOTE: In this example, VLAN 100 will be advertised to the switch using GVRP. Notice that
untagged 802.2 frames must be loaded to allow sending and receiving GVRP frames.
Switch ports must be configured with GVRP enabled.
• Example 9: 802.3ad with QASP
LOAD ODINEB.NLM
LOAD QASP.LAN FRAME=ETHERNET_II NAME=QASP_1_EII VSLOT=1 MODE=802.3ad
LOAD Q57.LAN FRAME=ETHERNET_II NAME=Q57_1_EII SLOT=1