Filter
Top Products
Quattro DC Quick Parameter Reference
Sub
menu
Parameter Units Range Default
Site
Setting
C2
Logic Inputs C2 Submenu – See Logic Inputs C2 submenu on page 61.
C2 N.C. INPUTS None Hex Number 0x01
C2 LOGIC INPUT 1 TB1(1)
CONTACT CFIRM
C2 LOGIC INPUT 2 TB1(2)
CTR PWR SENSE
C2 LOGIC INPUT 3 TB1(3)
NO FUNCTION
C2 LOGIC INPUT 4 TB1(4)
DRIVE ENABLE
C2 LOGIC INPUT 5 TB1(5)
RUN
C2 LOGIC INPUT 6 TB1(6)
UP/DWN
C2 LOGIC INPUT 7 TB1(7)
STEP REF B0
C2 LOGIC INPUT 8 TB1(8)
STEP REF B1
C2 LOGIC INPUT 9 TB1(9)
− contact cfirm
− ctr pwr sense
− drive enable
− extrn fault 1
− extrn fault 2
− extrn fault 3
− extrn /flt 4
− fault reset
− field enable
− low gain sel
− mech brk hold
− mech brk pick
− no function
− ospd test src
− pre-trq latch
− run
− run down
− run up
− s-curve sel 0
− s-curve sel 1
− ser2 insp ena
− step ref b0
− step ref b1
− step ref b2
− step ref b3
− trq ramp down
− up/dwn
FAULT RESET
C3 Logic Outputs C3 Submenu – See Logic Outputs C3 submenu on page 63.
C3
LOGIC OUTPUT 1
TB1(25)
CLOSE
CONTACT
C3
LOGIC OUTPUT 2
TB1(26)
RUN
COMMANDED
C3
LOGIC OUTPUT 3
TB1(27)
MTR OVERLOAD
C3
LOGIC OUTPUT 4
TB1(28)
ENCODER FLT
C3
LOGIC OUTPUT 5
TB1(29)
FAULT
C3
LOGIC OUTPUT 6
TB1(30)
SPEED REG
RLS
C3
LOGIC OUTPUT 7
TB1(31)
SPEED REG
RLS
C3
SSR1 TB1(21/22) NO FUNCTION
C3
SSR2 TB1(23/24) NO FUNCTION
C3
RELAY COIL 1 TB2
(1/3/5)
NO FUNCTION
C3
RELAY COIL 2 TB2
(8/10/12)
− alarm
− alarm+flt
− auto brake
− brake hold
− brake pick
− brk hold flt
− brk pick flt
− car going dwn
− car going up
− charge fault
− close contact
− contactor flt
− curr reg flt
− drv overload
− encoder flt
− fault
− flux confirm
− ground fault
− in low gain
− motor trq lim
− mtr overload
− no function
− not alarm
− over curr flt
− overspeed flt
− overtemp flt
− overvolt flt
− ovrtemp alarm
− phase fault
− ramp down ena
− ready 2 start
− ready to run
− regen trq lim
− run commanded
− run confirm
− speed dev
− speed dev low
− speed ref rls
− speed reg rls
− undervolt flt
− up to speed
− uv alarm
− zero speed
NO FUNCTION
C4 Analog Outputs C4 Submenu – See Analog Outputs C4 submenu on page 65.
C4
ANALOG OUTPUT 1
SPEED REF
C4 ANALOG OUTPUT 2
− arm current
− arm voltage
− aux torq cmd
− bus voltage
− est motor spd
− field current
− iarm error
− pretorque ref
− motor mode
− spd rg tq cmd
− speed command
− speed error
− speed feedbk
− speed ref
− tach rate cmd
− tach speed
− torque ref
SPEED FEEDBK
8