Filter
Top Products
Chapter 6 Appendix — Specications
180 - ENGLISH
Specications
The specications of the projector are as follows.
Power supply AC 120 V, 50 Hz/60 Hz
Power consumption
PT-DZ13KU 1 000 W (9.3 A)
PT-DS12KU, PT-DW11KU 980 W (9.1 A)
PT-DZ10KU 925 W (9 A)
0.2 W when [STANDBY MODE] is set to [ECO]
6 W when [STANDBY MODE] is set to [NORMAL]
DLP chip
Size
PT-DZ13KU, PT-DZ10KU 24.4 mm (0.96") (aspect ratio 16:10)
PT-DS12KU 24.1 mm (0.95") (aspect ratio 4:3)
PT-DW11KU 21.6 mm (0.85") (aspect ratio 16:9)
Display system 3-unit DLP chips, DLP type
Number of pixels
PT-DZ13KU, PT-DZ10KU 2 304 000 pixels (1 920 x 1 200 dots)
PT-DS12KU 1 470 000 pixels (1 400 x 1 050 dots)
PT-DW11KU 1 049 088 pixels (1 366 x 768 dots)
Lens Optional
Luminous lamp
PT-DZ13KU, PT-DS12KU,
PT-DW11KU
380 W UHM lamp x 2
PT-DZ10KU 355 W UHM lamp x 2
Light output
*1
PT-DZ13KU, PT-DS12KU 12 000 lm (ANSI)
PT-DW11KU 11 000 lm (ANSI)
PT-DZ10KU 10 600 lm (ANSI)
Contrast ratio
*1
10 000:1 (when [DYNAMIC IRIS] is set to [3])
Color system 7 standards (NTSC/NTSC4.43/PAL/PAL-N/PAL-M/SECAM/PAL60)
Projection screen size 1.78 m (70") to 25.40 m (1 000")
Screen aspect ratio
PT-DZ13KU, PT-DZ10KU 16:10
PT-DS12KU 4:3
PT-DW11KU 16:9
Projection method [FRONT/CEILING], [FRONT/FLOOR], [REAR/CEILING], [REAR/FLOOR]
Power cable length 3.0 m (118-1/8")
Outer case Molded plastic
Dimensions
Width 530 mm (20-7/8")
Height 200 mm (7-7/8") (with legs at shortest position)
Depth 548.5 mm (21-19/32") (excluding the lens)
Weight
Approx. 24.0 k] (52.9 lbs.)
*2
Noise level
*1
PT-DZ13KU, PT-DS12KU,
PT-DW11KU
45 dB
PT-DZ10KU 43 dB
Operating
environment
Operating
environment
temperature
*3
0 °C (32 °F) to 45 °C (113 °F)
Operating
environment
humidity
10 % to 80 % (no condensation)
Remote
control
Power supply DC 3 V (AA/R6 battery x 2)
Operating range Within approx. 30 m (98'5") (when operated directly in front of signal receiver)
Weight
134 ] (4.7 ozs.) (including batteries)
Dimensions Width: 51 mm (2"), Height: 176 mm (6-15/16"), Depth: 28 mm (1-3/32")
*1 Measurement, measuring conditions and method of notation all comply with ISO21118 international standards.
*2 Average value. Weight varies for each product.
*3 When using the projector at high altitudes (1 400 m (4 593') or higher – lower than 2 700 m (8 858') above sea level), the operating environment
temperature should be between 0 °C (32 °F) and 40 °C (104 °F).
If you use the Smoke cut lter, the operating environment temperature should be between 0 °C (32 °F) and 35 °C (95 °F). However, it cannot be
used at high altitudes.
If you use the Replacement lamp unit (for portrait mode), the operating environment temperature should be between 0 °C (32 °F) and 40 °C
(104 °F) when using the projector at elevations lower than 1 400 m (4 593') above sea level, and between 0 °C (32 °F) and 35 °C (95 °F) when
using the projector at high altitudes. If you use the Smoke cut lter together, the operating environment temperature should be between 0 °C (32 °F)
and 30 °C (86 °F).
If the [LAMP SELECT] menu is set to [DUAL], and [LAMP POWER] is set to [HIGH], [MIDDLE], or [NORMAL], and an ambient temperature reaches
40 °C (104 °F) or higher (35 °C (95 °F) or higher when [HIGH ALTITUDE MODE] is set to [ON] or the Smoke cut lter is used), the light output may
decrease by approx. 20 % to protect the projector.