Anritsu S331D Network Router User Manual


 
51) Power Meter Relative
52) Power Meter Relative
53) Power Meter Relative (lowest byte)
54) Power Meter Status (00h = Off, 01h = On)
55) Power Meter Unit (00h = Watts, 01h = dBm)
56) Power Meter Relative Status (00h = Off, 01h = On)
57) Power Meter Offset Status (00h = Off, 01h = On)
58) Power Meter RMS Averaging Level (00h = Off, 01h = Low, 02h = Medium, 03h = High)
59) Frequency Scale Factor
135
(higher byte)
60) Frequency Scale Factor (lower byte)
61) Frequency Range Minimum
136
(highest byte)
62) Frequency Range Minimum
63) Frequency Range Minimum
64) Frequency Range Minimum (lowest byte)
65) Frequency Range Maximum
137
(highest byte)
66) Frequency Range Maximum
67) Frequency Range Maximum
68) Frequency Range Maximum (lowest byte)
69) Zero Status (00h = Off, 01h = On)
70) Zero Value
138
(highest byte)
71) Zero Value
72) Zero Value
73) Zero Value (lowest byte)
74-120) Not Used
For T1 Mode (Option 50):
26) T1 Receive Input (00h: Terminate, 01h: Bridged, 02h: Monitor)
27) T1 Framing Mode (01h: ESF, 02h: D4SF)
28) T1 Line Coding (01h: B8ZS, 02h: AMI)
29) T1 Clock Source (00h: External, 01h: Internal)
30) T1 Tx Level (01h: 0 dB, 02h: -7.5 dB, 03h: -15 dB)
31) T1 Error Insert Type (00h: Frame Error, 01h: BPV, 02h: Bit Errors, 04h: RAI, 05h: AIS)
32) T1 Loop Code (00h: CSU, 01h: NIU, 02h: User 1, 03h: User 2)
33) T1 CRC Method (00h: ANSI CRC, 01h: Japanese CRC)
34) T1 Loop Type (00h: In Band, 01h: Data Link)
35) T1 Pattern (higher byte)
36) T1 Pattern (lower byte) 01h: PRBS-9, 02h: PRBS-11, 03h: PRBS-15, 04h: PRBS-20(O.151), 05h:
PRBS-20(O.153), 06h: PRBS-23, 07h: QRSS, 08h: 1 in 8, 09h: 2 in 8, 0Ah: 3 in 8, 0Bh: All Ones, 0Ch: All
Zeros, 0Dh: T1-DALY, 0Eh: User Defined)
37) T1 Pattern Invert Status (00h: Non-Inverted, 01h: Inverted)
38) T1 Display Type (00h: Histogram, 01h: Raw Data)
39) T1 Impedance
40 - 55) First User Defined Loop Code Down (16 bytes)
56 - 71) Second User Defined Loop Code Down (16 bytes)
72 - 87) First User Defined Loop Code Up (16 bytes)
88 - 103) Second User Defined Loop Code Up (16 bytes)
104 - 135) User Defined Pattern (32 bytes)
136) T1 1
st
User Defined Loop Up (higher byte)
46 Site Master PM
135 In number of Hz
136 Scaled by Frequency Scale Factor
137 Scaled by Frequency Scale Factor
138 Value sent as ((value in dBm * 1000) + 100)