Filter
Top Products
66
Screen display
<Operation related>
NO CF CARD!
(Flashing for 3 sec.)
PROTECT!
(Flashing for 3 sec.)
NO CLIP!
(Flashing for 3 sec.)
SET WLAN AD HOC MODE
OFF!
(Flashing for 3 sec.)
SET DHCP OFF!
(Flashing for 3 sec.)
OVERLAP HTTP!
(Flashing for 3 sec.)
OVERLAP ASF_HTTP!
(Flashing for 3 sec.)
OVERLAP ASF-RTSP!
(Flashing for 3 sec)
OVERLAP QT-RTSP!
(Flashing for 3 sec)
ILLEGAL SETTING!
(Flashing for 3 sec.)
DATA LENGTH 10 or 26
(Flashing for 3 sec)
CHRACTER IS SHORT!!
(Flashing for 3 sec)
SET LEAP MODE OFF!!
(Flashing for 3 sec)
SAME OLD PASSWORD!!
(Flashing for 3 sec)
GARBAGE! (Flashing display
while optimizing)
IP ADDRESS ERROR!
(Flashing display until network
connection is established)
NO UPDATE FILES!
(Flashing for 3 sec.)
NO UPDATE CARD!
(Flashing for 3 sec.)
UPDATE FAILED!
COPY GUARD!
Others Troubleshooting
Cause
There is no CF memory card inserted.
Deletion of a protected clip file was
attempted.
There is no CF memory card inserted, of
there is no clip file available.
Use of DHCP server was attempted
while in the AD HOC mode.
Selection of AD HOC mode was at-
tempted while using DHCP server.
Port set for HTTP for WEB Browser is
already in use.
Port set for HTTP for Media Player is
already in use.
Set port for RTSP for Streamproducer is
already in use by another port.
Set port for RTSP for Quick time is
already in use by another port.
Set value exceeded setting range.
Setting made with other than 10 or 26
characters.
Set number of characters is 2 or less / 3
or less.
Attempted to use LEAP while in the
ADHOC mode.
The new password is the same as the
old password.
Optimization of internal ROM disk
currently being processed.
Failed to acquire IP address when DHCP
is ON.
There is no update data in the CF
memory card.
CF memory card is not inserted.
Update was not successful.
Signal of recording origin is protected with
copy guard.
Remedy
Insert a CF memory card.
To delete the clip file, remove the
protection.
Check the CF memory card.
Set DHCP in the NETWORK SET menu
screen to OFF when using the AD HOC
mode.
Set WLAN AD MOC MODE in the
NETWORK SET menu screen to OFF
when using DHCP server.
Set an unused port.
Set an unused port.
Set an unused port.
Set an unused port.
Set a value within the setting range.
Set using 10 or 26 characters.
Set using 3 or more / 4 or more charac-
ters.
Set LEAP to OFF when in the ADHOC
mode.
Set a password different from the old
password.
Please wait until process is completed.
Set DHCP again.
Insert a CF memory card with UPDATE
data into the slot.
Insert a CF memory card with UPDATE
data into the slot.
Contact your JVC dealer.
Input recording signal with no copy guard
protection.
Reference
page
4
42
––
12
12
13, 52
13, 52
13, 52
13, 52
12
13
14
14
14
––
12
64
64
64
––
Memo
If the input signal is switched during transmission or CF recording, the video may flicker. However, the video will return to normal
after a certain time. (The time will differ depending on the selected encoding parameter.)
67
Others Checking communication/connection
By using the PING command standard to Windows, it is possible to check whether the connection is correct and that communication
can be made from the PC to SA-DV6000.
1.
Launch the command prompt.
● For Windows 2000
From the Start button, select [Programs] → [Accessories] → [Command Prompt].
2.
Input the following and press the Enter key.
PING xxx.xxx.xxx.xxx (xxx.xxx.xxx.xxx is the IP address of the other party)
Input example: When the IP address of the other party is "192.168.0.10"
PING 192.168.0.010
3.
Check to see that the other party is successfully displayed.
If connection is not successful, “Request timed out” or “Destination host unreachable” message will appear.