Filter
Top Products
57\``NY
COO
5ENZWLN XYW[,
DNYU - GNUX
5ENZWLN XYW[,
DNYUJVNV[
5ENZWT\[RWV
1.. MXR
5?>E UWMN
COO
5@; JL[RWV
>PVWYN 8E
5@; JL[RWV
8E JVM @;
5@; JL[RWV
>PVWYN @;
5@; JL[RWV
8E JVM @;
5AF< TJVP\JPN
9N\[ZLQ
5AF< TJVP\JPN
;YJVaJRZ
DJXNY [_XN
GQRLS
AD [YJ_ UWMN 5
;RYZ[
egjf
5AF< TJVP\JPN
:VPTRZQ
5AJV\JT :TN]J[N
C[QNYZ 5
pyx}vx~sr t{yw z{s*vy~| zqus
AD [YJ_ ZR`N
62 ,- @N[[NY
7\TS ONNMNY ZR`N
62 ,- @N[[NY
:V]NTWXN ZR`N
9@ ,- 7\ZRVNZZ
DJXNY [_XN
BWYUJT
9\XTN^ UWMN
BWVN
FWY[NY UWMN 5
F[JLSNY
6\[W LJZZN[[N
BWVN
5;WYU ;NNM
GRUNW\[ .1.ZNL,
egkf
5FTNNX [RUNY
.1. URV,
5DYRV[ =:I+9HAD
5@RZ[ WO
YNZRMNV[ ;WV[Z
5DYRV[NY ENZN[
5@; JL[RWV
@; WVT_
58E JL[RWV
8E WVT_
5B\UKNY WO XJPNZ
XYRV[NM ./01234
eglf
5?>E UWMN
CV
5?>E UWMN
CV
5:LWXYRV[ UWMN
COO
5?>E UWMN
CV
5DJPN XYW[NL[
6\[W
5ENZWT\[RWV
4.. MXR
5ENZWYLN XYW[,
COO
5DYRV[ MNVZR[_
.1
57\``NY
CV
5FNY]RLN 5
559N]NTWXNY
559Y\U
55DYRV[
F[J[\Z DJPN
egmf
egnf
egihf
*2: The printer can be set to print error data during KPDL emula-
tion. If this is set to 2Q, error data will be printed if trouble
occurs during printing. This is set to 2II before leaving the
factory.
*3: You can select either of two Courier fonts, Dark (bold) or Light
(thin), as the default font. The original selection is Dark. The
selection made applies to both bit map fonts and scalable
fonts; the two cannot be set independently.
*4: The !6L]H menu is not available for the Courier and Lette r-
Gothic fonts. Use the !3LWFK menu to scale these fixed
fonts.
*5: Any value from 0 to 495 [seconds] in 5-second increments.
(The printer does not time out with the value set to 0.)
*6: Any value from 0 to 120 [minutes] in 5-minute increments.
*7: This is the total number of pages printed by the printer up to
the present time.
*8: Auto is the default setting, and this selection does not usually
appear in the MODE SELECT menu. In the event of a 3ULQWý
RYHUUXQ 3UHVV &217,18( error due to insuffi-
cient printer memory, the printer automatically switches to
page protect mode 2Q. In such a case this selection will appear
in the MODE SELECT menu.
☛ In order to maintain efficient use of printer memory,
the setting should normally be set to $XWR.
*9: Resouce protection is available only when the printer has more
than 10 MB (14 MB if the duplexer is on) of additionally
installed main memory.
*10:For service purpose only.