Sony DVS-A3232 Switch User Manual


 
5-38
ROUTING SWITCHER SYSTEM (E)
5-2. Setting Items of the Secondary Station
SELECT REMOTE PROTOCOL DVS-V6464B V2.10 STATION NUMBER 1
SELECT RS-422 CHANNEL ? (A--B) A
 Ctrl-E:RETURN TO MENU
SELECT REMOTE PROTOCOL DVS-V6464B V2.10 STATION NUMBER 1
CHANNEL = A REMOTE = CART+ UA2 = 10000000
SET DESTINATION TRANSCODE( CN NUM.= REMOTE NUM.)
1=001 2=002 3=003 4=004 5=005 6=006 7=007 8=008
9=009 10=010 11=011 12=012 13=013 14=014 15=015 16=016
17=017 18=018 19=019 20=020 21=021 22=022 23=023 24=024
25=025 26=026 27=027 28=028 29=029 30=030 31=031 32=032
33=033 34=034 35=035 36=036 37=037 38=038 39=039 40=040
41=041 42=042 43=043 44=044 45=045 46=046 47=047 48=048
49=049 50=050 51=051 52=052 53=053 54=054 55=055 56=056
57=057 58=058 59=059 60=060 61=061 62=062 63=063 64=064
SET SOURCE TRANSCODE( CN NUM.= REMOTE NUM.)
1=001 2=002 3=003 4=004 5=005 6=006 7=007 8=008
9=009 10=010 11=011 12=012 13=013 14=014 15=015 16=016
17=017 18=018 19=019 20=020 21=021 22=022 23=023 24=024
25=025 26=026 27=027 28=028 29=029 30=030 31=031 32=032
33=033 34=034 35=035 36=036 37=037 38=038 39=039 40=040
41=041 42=042 43=043 44=044 45=045 46=046 47=047 48=048
49=049 50=050 51=051 52=052 53=053 54=054 55=055 56=056
57=057 58=058 59=059 60=060 61=061 62=062 63=063 64=064
CAS=065
F1:REMOTE F2:DEFAULT F3:DEST. F4:SOURCE Ctrl-E:RETURN TO MENU
U: SELECT REMOTE PROTOCOL
Purpose
This menu is used to set channels A and B of REMOTE 2
(D-sub 9-pin) to loop-through. When the REMOTE 2
control mode is set to DIRECT, this menu is used to set the
protocol and the conversion table of the input/output
numbers.
There are three kinds of protocols.
. PRODUCTION SWITCHER PROTOCOL
. AUDIO MIXER PROTOCOL
. CART PROTOCOL
n
AUDIO MIXER PROTOCOL was known as “SWITCH-
ER PROTOCOL” before.
Set the conversion table of the input/output numbers so
that the input/output numbers defined by the external
controller will correspond to those of the routing switcher.
In the THROUGH mode, there will be no setting menu for
channel B. For details of the DIRECT mode, refer to the
menu item [U : SELECT CONTROL MODE] in the
primary station.
Setting Procedure
1. Select menu item [U].
2. “SELECT RS-422 CHANNEL =? (A B) A” will be
displayed. Input A or B using the alphabet keys and
press [Enter]. The screen will change to the setting
screen of the selected channel.
3. The cursor will be placed at “1=001” of “SET DESTI-
NATION TRANSCODE”.
When [Enter] is pressed, “1=” will be displayed and
the number can be typed. The left “1” in “1=001”
indicates the input/output number of the switcher and
the right “001” indicates the command number
received.
4. Input a number between 1 and 128 and press [Enter]
set it. The cursor will move to the next number.
If “00” is input, “001” will be displayed. If number
129 or later is input, the previous number will be
displayed. If [Enter] is pressed without inputting
anything, invalid crosspoints will be set so that the
screen will show “ · · · · ”, and the cursor will move to
the next number. When [Ctrl] _ [F] is pressed before
the setting, the previous number will be displayed and
the cursor will move to the next number.
n
The same number cannot be set to more than one place. If
the same number is used, the message “* * * is used
already; Ignored” will be displayed and the cursor will stop
at its current position.
Example of Setting Screen
Operating Function Keys
[F1] : REMOTE (To switch the protocol)
1. When [F1] is pressed, the cursor will move to
“REMOTE”.
2. When [Enter] is pressed, the protocol will be
switched. To change the “* * *” of “UA2 =”,
select the desired position with the cursor and
press [Enter] to switch 1/0 alternately.
n
The description “* * *” of “UA2 =* * *” on the above
menu corresponds to the DIP switch setting which LSB is
at the left end.
[F2] : DEFAULT (Initializing the data)
1. When [F2] is pressed, “DEFAULT ok? (y/n)”
will be displayed at the bottom of the screen.
2. When [Y] is pressed, the program will be
executed. When [N] is pressed, it will not be
executed.
[F3] : DEST
When [F3] is pressed, the cursor will move to the
destination side.
[F4] : SOURCE
When [F4] is pressed, the cursor will move to the
source side.