Barco HDX W12 Projector User Manual


 
1. Safety
the potential risk to themselves or other persons. The term USER and OPERATOR refers to any person other than SERVICE PER-
SONNEL, AUTHORIZED to operate professional projection systems.
A HDX projector is intended "FOR PROFESSIONAL USE ONLY" by AUTHORIZED PERSONNEL familiar with potential hazards
associated with high voltage, high intensity light beams, ultraviolet exposure and high temperatures generated by the lamp and
associated circuits. Only qualied SERVICE PERSONNEL, knowledgeable of such risks, are allowed to perform service functions
inside the product enclosure.
1.2 Important safety instructions
To prevent the risk of electrical shock
This product should be operated from a mono phase AC power source.
This apparatus must be grounded (earthed) via the supplied 3 conductor AC power cable. If none of the supplied power cables
are the correct one, consult your dealer.
If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the
purpose of the grounding-type plug.
Do not allow anything to rest on the power cord. Do not locate this product where persons will walk on the cord. To disconnect
the cord, pull it out by the plug. Never pull the cord itself.
Use only the power cord supplied with your device. While appearing to be similar, other power cords have not been safety
tested at the factory and may not be used to power the device. For a replacement power cord, contact your dealer.
Do not operate the projector with a damaged cord. Replace the cord.
Do not operate the projector if the projector has been dropped or damaged - until it has been examined and approved for
operation by a qualied service technician.
Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.
If an extension cord is necessary, a cord with a current rating at least equ
al to that of the projector should be used. A cord rated
for less amperage than the projector may overheat.
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short out
parts that could result in a risk of re or electrical shock.
Do not expose this projector to rain or moisture.
Do not immerse or expose this projector in water or other liquids.
Do not spill liquid of any kind on this projector.
Should any liquid or solid object fall into the cabinet, unplug the set and have it checked by qualied service personnel before
resuming operations.
Do not disassemble this projector, always take it to an authorized trained service person when service or repair work is required.
Do not use an accessory attachment which is not recommended by the manufacturer.
Lightning - For added protection for this video product during a lightning storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet. This will preven
t damage to the device due to lightning and AC power-line surges.
To prevent personal injury
Isolate electrically before replacing the lamp or lamp house. Caution: Hot lamp (house).
Caution: High pressure lamp may explode if improperly handled. Refer servicing to qualied service personnel.
To prevent injury and physical damage, always read this manual and all labels on the system before inserting the lamp casing,
connecting to the wall outlet or adjusting the projector.
To prevent injury, take note of the weight of the projector. Minimum 4 persons are needed to carry the projector.
To prevent injury, ensure that the lens and all covers are correctly installed. See installation procedures.
Warning: high intensity light beam. NEVER look into the lens ! High luminance could result in damage to the eye.
Warning: extremely high brightness lamps: This projector uses extr
emely high brightness lamps. Never attempt to look
directly into the lens or at the lamp. If the projection distance is less than 6 meter, any person needs to be at least 4 meters
away from the projected image. Avoid close range reection of the projected image on any reecting surface (such as glass,
metal, …) . When operating the projector, we strongly
recommend wearing suitable safety glasses.
Before attempting to remove any of the projector’s covers, you must turn off the projector and disconnect from the wall outlet.
When required to switch off the projector, to access parts inside, always disconnect the power cord from the power net.
The power input at the projector side is considered as the disconnect device. When required to switch off the projector, to
access parts inside, always disconnect the power cord at the projector side. In case the power input at the projector side is not
accessible (e.g. ceiling mount), the socket outlet supplying the projector shall be installed nearby the projector and be easily
accessible, or a readily accessible general disconnect device shall be incorporated in the xed wiring.
Never stack more than two (2) HDX projectors in a hanging conguration (truss) and never stack more than three (3) HDX
projectors in a base stand conguration (table mount).
When using the projector in a hanging conguration, always mount 2 safety cables. See installation manual for the correct use
of these cables.
Do not place this equipment on an unstable cart, stand, or table. The product may fall, causing serious damage to it and
possible injury to the user.
8
R5905032 HDX SERIES 02/03/2015