Filter
Top Products
Conettix D6600/D6100 | Computer Interface Manual | Appendix C: Modem IIIa2 Messages
.
Bosch Security Systems, Inc. | 1/07 | 4998122703-01 109
Table 92: Modem IIIa
2
Messages (continued)
Event Device/Mode Display Explanation Refer to Section
C.1 Zonex and
Comex
Translation on
page 137.
563.
RAM Access
Fail
(No Call Back)
Printer:
D6500 Mode:
SIA Mode:
dd/dd tt:tt Lxx ACC aaaa RAM ACCESS FAIL
+++ ACC aaaa PHONE#=h
h1rrlssssssaaaasTsssFt
<header>[#aaaa|NphhRU]
An unsuccessful
attempt was made by a
RAM to contact the
account on the
PHONE# specified in
the second line of the
report.
564.
RAM Access
OK
(from Call
Back)
Printer:
D6500 Mode:
SIA Mode:
dd/dd tt:tt Lxx ACC aaaa RAM ACCESS OK
+++ ACC aaaa PHONE#=h
h1rrlssssssaaaasRsssFt
<header>[#aaaa|NphhRS]
The account was
contacted by a RAM
on the PHONE#
specified in the second
line of the report.
565.
RAM Access
OK
(via Phone
Line)
Printer:
D6500 Mode:
SIA Mode:
dd/dd tt:tt Lxx ACC aaaa RAM ACCESS OK
h1rrlssssssaaaasRsssFt
<header>[#aaaa|NRS]
The account was
contacted by a RAM
on the PHONE#
specified in the second
line of the report.
566.
Re-Boot
Printer:
D6500 Mode:
SIA Mode:
dd/dd tt:tt Lxx ACC aaaa RE-BOOT
h1rrlssssssaaaasNsD14t
<header>[#aaaa|NRR]
The control panel was
reset.
567.
Re-Boot
Printer:
D6500 Mode:
SIA Mode:
dd/dd tt:tt Lxx ACC aaa RESTORAL ZN 9
h1rrlssssssaaaasRsss9t
<header>[#aaaa|NUR9]
Battery restoral report,
control panel reboot,
watchdog reset, power
reset, or ResetBye with
RAM.
Control panel reboot,
watchdog reset, power
reset, or ResetBye with
RAM (can also be
Battery Restoral
Report for D7112).
2,
D9112
568.
Re-Boot
(SDI Device
and Point
reported)
Printer:
D6500 Mode:
SIA Mode:
dd/dd tt:tt Lxx ACC aaaa RE-BOOT
+++ ACC aaaa POINT=ppp SDI=ddd
h1rrlssssssaaaasNspppt
<header>[#aaaa|NpidddRRppp]
The control panel was
reset.
569.
Reject
Command
Printer:
D6500 Mode:
SIA Mode:
dd/dd tt:tt REJECT COMMAND RCVR rr
h3rrsREJECT COMMANDsst
<LF><CR><TAB><seq#><rec#><line#>[REJECT
COMMAND]<CR>
570.
Relay Reset
(by
Programmer)
Printer:
D6500 Mode:
SIA Mode:
dd/dd tt:tt Lxx ACC aaaa RELAY RESET
+++ ACC aaaa BY PROGRAMMER
+++ ACC aaaa RELAY#=rrr SDI=ddd
h1rrlssssssaaaasNsD22t
<header>[#aaaa|NpidddROrrr]
The RELAY specified
in the second line of
the report was reset.
571.
Relay Reset
(by RAM)
Printer:
D6500 Mode:
SIA Mode:
dd/dd tt:tt Lxx ACC aaaa RELAY RESET
+++ ACC aaaa BY REMOTE
+++ ACC aaaa RELAY#=rrr
h1rrlssssssaaaasNsD24t
<header>[#aaaa|NROrrr]
The RELAY specified
in the second line of
the report was reset.
572.
Relay Reset
(by SKED)
Printer:
D6500 Mode:
SIA Mode:
dd/dd tt:tt Lxx ACC aaaa RELAY RESET
+++ ACC aaaa BY SKED
+++ ACC aaaa RELAY#=rrr SKED=kk
h1rrlssssssaaaasNsD20t
<header>[#aaaa|NaikkROrrr]
The RELAY specified
in the second line of
the report was reset.