Filter
Top Products
Line 1
Message
Line 2
Message
Causes
Corrective Actions
SYSTEM
ID
SYSTEM NAME
SYSTEM ID is a unique name, five
characters or less, defined by the user.
SYSTEM NAME is a unique name, 16
characters or less, defined by the user.
The system ID and name display under
the following conditions:
l The system is powered on.
l The power is off and active POST
errors are displayed.
This message is for information only.
You can change the system ID and name in the System Setup program (see "Using
the System Setup Program").
E0000
OVRFLW CHECK
LOG
LCD overflow message.
A maximum of three error messages can
display sequentially on the LCD. The
fourth message displays as the standard
overflow message.
Check the SEL for details on the events.
E0119
TEMP AMBIENT
Ambient system temperature is out of
acceptable range.
Ensure that the system cooling fans are properly installed. If the problem persists,
replace the faulty fan(s) (see "System Fans").
E0119
TEMP BP
Backplane board is out of acceptable
temperature range.
Ensure that the system cooling fans are properly installed. If the problem persists,
replace the faulty fan(s) (see "System Fans"). If the problem persists, replace the
backplane board (see "SCSI Backplane Board").
E0119
TEMP CPU n
Specified microprocessor is out of
acceptable temperature range.
Ensure that the system cooling fans are properly installed. If the problem persists,
replace the faulty fan(s) (see "System Fans"). If the problem persists, ensure that the
specified microprocessor's heat sink is properly installed. If the problem persists,
replace the faulty microprocessor (see "Microprocessors").
E0119
TEMP SYSTEM
System board is out of acceptable
temperature range.
Ensure that the system cooling fans are properly installed. If the problem persists,
replace the faulty fan(s) (see "System Fans"). If the problem persists, replace the
system board (see "System Board").
E0212
VOLT 3.3
System power supply is out of acceptable
voltage range; faulty or improperly
installed power supply.
Ensure that the power supplies are properly installed. If the problem persists, replace
the faulty power supply(s) (see "Power Supplies").
E0212
VOLT 5
E0212
VOLT 12
E0212
VOLT BATT
Faulty battery; faulty system board.
Ensure that the system battery is properly installed. If the problem persists, replace
the battery (see "System Battery"). If the problem persists, replace the system board
(see "System Board").
E0212
VOLT BP 12
Backplane board is out of acceptable
voltage range.
Ensure that the power cables are securely connected to the backplane board (see
"SCSI Backplane Board"). Ensure that the power supplies are properly installed. If the
problem persists, replace the faulty power supply(s) (see "Power Supplies").
E0212
VOLT BP 3.3
E0212
VOLT BP 5
E0212
VOLT CPU VRM
Microprocessor VRM voltage is out of
acceptable range; faulty or improperly
installed microprocessor VRM; faulty
system board.
Ensure that supported VRMs of the same type are properly installed. If the problem
persists, replace the VRMs (see Figure4-29). If the problem persists, replace the
system board (see "System Board").
E0212
VOLT NIC
1.8V
Integrated NIC voltage is out of
acceptable range; faulty or improperly
installed power supply; faulty system
board.
Ensure that the power supplies are properly installed. If the problem persists, replace
the faulty power supply(s) (see "Power Supplies"). If the problem persists, replace
the system board (see "System Board").
E0212
VOLT NIC
2.5V
E0212
VOLT PLANAR
REG
System board is out of acceptable voltage
range; faulty or improperly installed
system board.
E0276
CPU VRM n
Specified microprocessor VRM is faulty,
unsupported, improperly installed, or
missing.
Ensure that supported VRMs of the same type are properly installed. If the problem
persists, replace the VRM (see Figure4-29).
E0276
MISMATCH VRM
n
E0280
MISSING VRM
n
E0319
PCI OVER
CURRENT
Faulty or improperly installed expansion
card.
Ensure that the expansion cards are properly installed. If the problem persists,
replace the faulty expansion card(s) (see "Expansion Cards").
E0412
RPM FAN n
Specified cooling fan is faulty, improperly
installed, or missing.
Ensure that the system cooling fans are properly installed. If the problem persists,
replace the faulty fan(s) (see "System Fans").
E0780
MISSING CPU
n
Microprocessor is not installed in the
specified socket.
A microprocessor must be installed in socket 1, and a VRM must be installed for each
installed microprocessor. Install a microprocessor in the specified socket or remove
the VRM for the specified microprocessor if that microprocessor is not installed (see
"Microprocessors"). To identify the microprocessors and VRMs, see Figure5-3.
E07F0
CPU IERR
Faulty or improperly installed
microprocessor.
Ensure that the microprocessors are properly installed. If the problem persists,
replace the faulty microprocessor(s) (see "Microprocessors").
E07F1
TEMP CPU n
HOT
Specified microprocessor is out of
acceptable temperature range and has
halted operation.
Ensure that the system cooling fans are properly installed. If the problem persists,
replace the faulty fan(s) (see "System Fans"). If the problem persists, ensure that the
microprocessor heat sinks are properly installed. If the problem persists, replace the
faulty microprocessor (see "Microprocessors").
E07F4
POST CACHE
Faulty or improperly installed
microprocessor.
Ensure that the microprocessors are properly installed. If the problem persists,
replace the faulty microprocessor(s) (see "Microprocessors").
E07F4
POST CPU REG
E07F4
POST CPU SMI
SMI handler failed to initialize; faulty
system board.
Replace the system board (see "System Board").