Filter
Top Products
8. Programmable Features
74
Helpful hints:
L To exit programming, press {OFF} any time.
Setting ringer tone for external calls
To set the handset ringer tone from one of 6
patterns for external calls. You can select “1”
(default), “2”, “3”, “4”, “5” or “6”.
Make sure the handset is not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Ringer setting” by pressing
{v} or {e}, and press {>}.
3. Scroll to “Ringer tone” by pressing {v} or
{e}, and press {>}.
4. Press {v} or {e} repeatedly to select the
desired setting.
L You can also select the ringer tone by
pressing a dialing button {1} to {6}.
5. Press the right soft key ({SAVE}).
6. Press {OFF}.
Note:
L To set the base unit ringer tone, see feature
#17 on page 69.
Setting incoming call tone
During an intercom call (page 45), while using
the room monitor feature (page 48) or while
listening to messages (page 62, 64), you can be
informed by 2 tones if a call arrives.
“2” (default): The incoming call tone will sound
twice.
“On”: The incoming call tone will be heard for as
long as the line rings.
“Off”: Deactivates this feature.
– Handset incoming call tone
Make sure the handset is not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Ringer setting” by pressing
{v} or {e}, and press {>}.
3. Scroll to “Incoming call” by pressing {v}
or {e}, and press {>}.
4. Press {v} or {e} repeatedly to select the
desired setting.
5. Press the right soft key ({SAVE}).
6. Press {OFF}.
– Base unit incoming call tone
Use the handset. Make sure the base unit and
the handset are not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Initial setting” by pressing
{v} or {e}, and press {>}.
3. Scroll to “Set base unit” by pressing {v}
or {e}, and press {>}.
4. Press {>} at “Incoming call”.
5. Press {v} or {e} repeatedly to select the
desired setting.
6. Press the right soft key ({SAVE}).
7. Press {OFF}.
Note:
L You can also program the base unit incoming
call tone with the base unit (feature #73 on
page 72).
Changing the handset display contrast
You can program the handset display contrast
from 6 levels. The default setting is level 3.
Make sure the handset is not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Initial setting” by pressing
{v} or {e}, and press {>}.
3. Press {>} at “LCD contrast”.
4. Press {v} or {e} repeatedly to select the
desired setting.
5. Press the right soft key ({SAVE}).
6. Press {OFF}.
Note:
L To change the base unit display contrast, see
feature #39 on page 70.
Setting auto talk feature
This feature allows you to answer a call by lifting
the handset off the charger without pressing
{TALK} or {SP-PHONE}. The default setting is
OFF.
Make sure the handset is not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Initial setting” by pressing
{v} or {e}, and press {>}.
3. Scroll to “Auto talk” by pressing {v} or
{e}, and press {>}.
4. Press {v} or {e} repeatedly to select the
desired setting.
5. Press the right soft key ({SAVE}).
6. Press {OFF}.
Note:
L If you subscribe to Caller ID service and want
to view the caller’s information on the
handset display after lifting up the handset to
answer a call, turn OFF this feature.
Setting dialing mode
If you cannot make calls, change this setting
depending on your telephone line service.
“Tone” (default): For tone dial service.
0519_FPG381.book Page 74 Monday, May 19, 2003 6:46 PM