Filter
Top Products
8. Programmable Features
75
“Pulse”: For rotary pulse dial service.
Make sure the base unit and the handset are
not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Initial setting” by pressing
{v} or {e}, and press {>}.
3. Scroll to “Set tel line” by pressing {v}
or {e}, and press {>}.
4. Press {>} at “Set dial mode”.
5. Press {v} or {e} repeatedly to select the
desired setting.
6. Press the right soft key ({SAVE}).
7. Press {OFF}.
Note:
L You can also program this feature with the
base unit (feature #13 on page 69).
Setting the flash time
The flash time depends on your telephone
exchange or host PBX.
You can select: “90ms” (milliseconds), “100ms”,
“110ms”, “250ms”, “300ms”, “400ms”, “600ms”
or “700ms” (default).
Make sure the base unit and the handset are
not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Initial setting” by pressing
{v} or {e}, and press {>}.
3. Scroll to “Set tel line” by pressing {v}
or {e}, and press {>}.
4. Scroll to “Set flash time” by pressing
{v} or {e}, and press {>}.
5. Press {v} or {e} repeatedly to select the
desired setting.
6. Press the right soft key ({SAVE}).
7. Press {OFF}.
Note:
L If the unit is connected via a PBX, PBX
functions (transferring a call etc.) might not
work correctly. Consult your PBX supplier for
the correct setting.
L You can also program this feature with the
base unit (feature #72 on page 72).
Setting line mode
The default setting of the line mode is “B”.
Generally leave this setting to “B”. If a change of
the line mode setting is required by our customer
call center or service personnel, change the line
mode to “A”.
Make sure the base unit and the handset are
not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Initial setting” by pressing
{v} or {e}, and press {>}.
3. Scroll to “Set tel line” by pressing {v}
or {e}, and press {>}.
4. Scroll to “Set line mode” by pressing {v}
or {e}, and press {>}.
5. Press {v} or {e} repeatedly to select the
desired setting.
6. Press the right soft key ({SAVE}).
7. Press {OFF}.
Note:
L You can also program this feature with the
base unit (feature #62 on page 72).
Changing the ring setting in TAM/FAX
mode
To change the number of rings before the unit
answers a call in TAM/FAX mode. You can select
“2” (default), “3”, “4”, “5”, “6”, “7” or “Toll
saver”. See page 55 for details.
Make sure the base unit and the handset are
not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Initial setting” by pressing
{v} or {e}, and press {>}.
3. Scroll to “Set answering” by pressing {v}
or {e}, and press {>}.
4. Press {>} at “Number of rings”.
5. Press {v} or {e} repeatedly to select the
desired setting.
L You can also select the number of rings by
pressing a dialing button {0} (“Toll
saver”), or {2} to {7}.
6. Press the right soft key ({SAVE}).
7. Press {OFF}.
Note:
L You can also program this feature with the
base unit (feature #06 on page 69).
Changing the maximum recording time for
each incoming message
“1min”, “2min” or “3min” (default): 1 minute to 3
minutes.
“Greeting only”: Only plays your greeting
message.
Make sure the base unit and the handset are
not being used.
1. Press {CONF/FUNCTION}.
2. Scroll to “Initial setting” by pressing
{v} or {e}, and press {>}.
0519_FPG381.book Page 75 Monday, May 19, 2003 6:46 PM