Filter
Top Products
[READY]
The countdown timer is displayed after 30 seconds without input signal. The projection lamp turns off
and cools down when reaching the set time, meanwhile the projector is in the power management
mode. The projection lamp will be turned on if the input signal is reconnected or any button is pressed.
[SHUT DOWN]
The countdown timer is displayed after 30 seconds without input signal. The projection lamp is turned
off and cooled down when reached the set time, then the projector enter into standby status.
[OFF]
Power management function is off.
Setting [TIMER]
The timer can be set to 5-120 minutes. The increment is 5 minutes.
Press 1) as to select [TIMER].
Press 2) qw to set the timer (5-120 MIN.).
The time will switch each time you press the button. f
Setting [STANDBY MODE] in step 3)
Set the power consumption during standby.
Press 1) as to select [STANDBY MODE].
Press 2) qw to switch the item.
The items will switch each time you press the button. f
[ECO]
Restricts some functions in the standby mode to reduce power consumption.
[NETWORK]
Restricts network function in the standby mode.
[NORMAL]
Does not restrict network function and serial communication function even in the standby mode.
Note
If [STANDBY MODE] is set to [ECO], you cannot use network functions when the projector is standing by. Also, you cannot f
use some RS-232C protocol commands.
When set to [ECO], it may take approx. 10 seconds longer before the projector starts projecting after the power is turned on, f
compared with when [NORMAL] is set.
If [STANDBY MODE] is set to [NETWORK], it takes less power consumption than it is set to [NORMAL]. f
When [STANDBY MODE] is set to [NETWORK], it will be no restriction for network function and serial communication f
function within 60 seconds when the Wake on LAN function is working.
The setting of [STANDBY MODE] cannot be returned to the factory default even if the [PROJECTOR SETUP] menu → f
[INITIALIZE ALL] is executed (Æpage 81).
[EMULATE]
When controlling the projector on a computer via the <SERIAL IN> terminal, set use of control commands on a previously
purchased Panasonic projector. This allows the control software for an existing Panasonic projector to be inherited and used.
Press 1) as to select [EMULATE].
Press the <ENTER> button.2)
The [EMULATE] screen is displayed. f
Press 3) as to switch the item.
The items will switch each time you press the button. f
[DEFAULT]
VW345N series, VX415N series, VW340Z, VX410Z, VX42Z, RZ475 series, RZ470 series, RW430
series, RZ370 series, RW330 series
[D3500]
D3500 series
[D4000]
D4000 series
[D/W5k SERIES]
D5700 series, DW5100 series, D5600 series, DW5000 series, D5500 series
[D/W/Z6k SERIES]
DZ770 series, DW740 series, DX810 series, DZ680 series, DW640 series, DX610 series,
DW730 series, DX800 series, DZ6710 series, DZ6700 series, DW6300 series, D6000 series,
D5000 series, DZ570 series, DW530 series, DX500 series
[L730 SERIES]
L730 series, L720 series, L520 series
[L780 SERIES]
L780 series, L750 series
[L735 SERIES]
L735 series
[L785 SERIES]
L785 series
[F/W SERIES]
FW430 series, FX400 series, FW300 series, F300 series, F200 series, FW100 series, F100 series
[LZ370]
LZ370 series
[LB/W SERIES]
LB3 series, LB2 series, LB1 series, ST10 series, LB90 series, LW80NT series, LB80 series,
LB78 series, LB75 series
[VX500 SERIES]
VW435N series, VW440 series, VW430 series, VX505N series, VX510 series, VX500 series,
VW330 series, VX400NT series, VX400 series, VX41 series
ENGLISH
-
77
Chapter 4 Settings - [PROJECTOR SETUP] menu