Filter
Top Products
– 84 –
Chapter 10 Menu Operations — Menu list
Menu list
[SYSTEM SETTINGS]
Sets the system in general.
f
is the extended menu. Set [MENU] → [CAMERA SETTINGS] → [Enhanced] → [Enhanced SW] to [ON] to display the extended menu.
Item Description of settings
[SYSTEM MODE] [FREQUENCY] Sets the system frequency.
If the setting of this item is changed, the device must be restarted. If a restart is required, a conrmation
dialog will be shown.
The camera’s system operation are determined by three settings: [FREQUENCY], [PIXEL], and [MAIN
CODEC]. Check to see if the three settings are matched.
[23.98p], [25.00p], [29.97p], [50.00p], [59.94p]
f Factory setting: [23.98p]
[PIXEL] Sets the main recorder’s number of recording pixels.
[4096×2160], [3840×2160], [1920×1080]
f Factory setting: [4096×2160]
[MAIN CODEC] Sets the main recorder’s recording codec. Selectable items vary depending on the [FREQUENCY]/[PIXEL]
setting.
[AVC-Intra4K 422], [AVC-Intra100]
f Factory setting: [AVC-Intra4K 422]
[SUB CODEC] Sets the sub recorder’s recording codec. Selectable items vary depending on the [FREQUENCY]/[PIXEL]
setting.
At the same time, this enables/disables proxy data recording.
[AVC-Intra2K 422], [AVC-Intra100], [AVC-LongG50], [AVC-LongG25], [AVC-Intra2K 422 & Pxy],
[AVC-Intra100 & Pxy], [AVC-LongG50 & Pxy], [AVC-LongG25 & Pxy], [OFF]
f Factory setting: [AVC-Intra2K 422]
[COLOR SETTING] [MAIN] Sets the colors of videos (entire camera system) recorded in the main recorder.
[V-Log]/[V-709]/[3D LUT]
f Factory setting: [V-Log]
[GRADING] Sets whether to apply the grading process.
This only enabled when [V-Log] is set in [MAIN].
[ON], [OFF]
f Factory setting: [OFF]
[SUB] Sets the colors of videos (entire camera system) recorded in the sub recorder.
Selectable items vary depending on the [MAIN] setting.
When [MAIN] is set to [V-Log] and [GRADING] is set to [ON]
[V-Log]/[GRADING]
When [MAIN] is set to [V-Log] and [GRADING] is set to [OFF]
[V-Log]/[V-709]
When [MAIN] is set to [V-709]
[V-709]
When [MAIN] is set to [3D LUT]
[3D LUT]
f Factory setting: [V-Log]
[3D LUT] Sets the grading process method when [GRADING] is set to [ON].
When [GRADING] is set to [ON]
[OFF]/[V-709]/[LOADED FILE]/[FILE SEL]
When [GRADING] is set to [OFF]
[OFF]
f Factory setting: [OFF]
[CDL] Sets the grading process method when [GRADING] is set to [ON].
When [GRADING] is set to [ON]
[ON], [OFF]
When [GRADING] is set to [OFF]
[OFF]
f Factory setting: [OFF]
[MON 1] Sets the output image from the <MON OUT1> terminal.
Selectable items vary depending on the [MAIN] setting.
When [MAIN] is set to [V-Log] and [GRADING] is set to [ON]
[V-Log]/[GRADING]
When [MAIN] is set to [V-Log] and [GRADING] is set to [OFF]
[V-Log]/[V-709]
When [MAIN] is set to [V-709]
[V-709]
When [MAIN] is set to [3D LUT]
[3D LUT]
f Factory setting: [V-Log]