Filter
Top Products
– 95 –
Chapter 10 Menu Operations — Menu list
Item Description of settings
[A.IRIS WINDOW]
Selects the auto iris detection window.
[NORMAL1]: Window that is near screen center.
[NORMAL2]: Window that is near screen bottom.
[CENTER]: Window that is a spot in the screen center.
f Factory setting: [NORMAL1]
[A.IRIS PEAK/AVE]
Sets the ratio included in the peak for auto iris standard.
[0] - [100]
f Factory setting: [30]
[LENS CONNECT
TYPE]
Sets the type of lens to be connected.
[TYPE B]: Lens controlled with 12-pin connector
[TYPE C]: Lens controlled with cooke/i communication
[OFF]: Other lenses
f Factory setting: [OFF]
[REC SETTINGS]
The various setting items of the recording function of the camera.
Item Description of settings
[FILE SPLIT] Sets whether to split the recording le by units of 4 GB or just maintain one le, when the following two
conditions are met:
f When OP-1b format codec is selected in [MENU] → [SYSTEM SETTINGS] → [SYSTEM MODE] →
[MAIN CODEC]/[SUB CODEC].
f When the recording size exceeds 4 GB
[ONE FILE]: Records in one le.
[SPLIT]: Splits the clip every 4 GB.
f Factory setting: [SPLIT]
When [MAIN CODEC] is in the OP-Atom format, [SUB CODEC] is also xed to [SPLIT].
[TC] [SET TC] Sets the default value of the time code to record.
Hour: [00] - [23]
Minute: [00] - [59]
Second: [00] - [59]
Frame: [00] - [23] (for [48p], [24p], [23.98p]), [00] - [23] (for [50i], [50p], [25p]), [00] - [29] (for [59.94i],
[59.94p], [29.97p])
f Factory setting: [00] (various items)
[SET UB] Sets user bits. Enabled only when [USER] is selected in [UB MODE].
This can be set by each digit from [00] to [FF].
f Factory setting: [00]
[TC/UB/Dur.] Switches the time code display to the user bits and duration counter display.
[TC], [UB], [Dur.]
f Factory setting: [TC]
[FREE/REC RUN] Sets the operation mode to advance the built-in time code generator.
[FREE RUN]: Advances regardless of the operation mode.
[REC RUN]: Advances when recording is in process.
f Factory setting: [FREE RUN]
[DF/NDF] Sets count method for the built-in time code generator of the camera.
[DF]: Uses the drop frame mode.
[NDF]: Uses the non-drop frame mode.
f Factory setting: [DF]
Enabled only when [59.94i], [59.94p], or [29.97p] is selected in [MENU] → [SYSTEM SETTINGS] →
[SYSTEM MODE] → [FREQUENCY].
[UB MODE] Selects the user bits mode.
[FRAME RATE]: Selects camera imaging information (such as frame rate).
[USER]: Selects the user bits value that has been set.
[EXT INPUT]: Records the user bits values currently input to the <TC IN/OUT> terminal.
[TIME]: Selects the local time. (hh, mm, ss)
[DATE]: Selects the local date and time. (YY, MM, DD, hh)
f Factory setting: [FRAME RATE]
[TC IN/OUT SEL] Sets the input/output of the <TC IN/OUT> terminal.
[TC IN], [TC OUT]
f Factory setting: [TC OUT]
[TC OUT] Selects the time code output to the <TC IN/OUT> terminal.
[TCG], [TCG/TCR]
f Factory setting: [TCG]
[TC OUT REF] Sets the output delay of the time code output from the <TC IN/OUT> terminal.
[RECORDING], [SDI OUT]
f Factory setting: [RECORDING]
[REC METADATA] [LOAD] Loads the metadata upload le saved to the SD memory card.
[RECORD] Sets whether to add loaded metadata at a recording.
[ON]: Adds metadata.
[OFF]: Does not add metadata.
f Factory setting: [OFF]