Filter
Top Products
D 13373.08
NOVEMBER 2007
MPS
Table of
Contents
TANDBERG MPS
ADMINISTRATOR GUIDE
Introduction
For your protection please read these safety instructions
completely before you connect the equipment to the power
source. Carefully observe all warnings, precautions and
instructions both on the apparatus and in these operating
instructions.
Retain this manual for future reference.
Water and Moisture
Do not operate the apparatus under or near water – for •
example near a bathtub, kitchen sink, or laundry tub, in a wet
basement, near a swimming pool or in other areas with high
humidity.
Never install jacks for communication cables in wet locations •
unless the jack is specifically designed for wet locations.
Do not touch the product with wet hands.•
Cleaning
Unplug the apparatus from communication lines, mains power-•
outlet or any power source before cleaning or polishing.
Do not use liquid cleaners or aerosol cleaners. •
Use a lint-free cloth lightly moistened with water for cleaning •
the exterior of the apparatus.
Ventilation
Do not block any of the ventilation openings of the apparatus. •
Never cover the slots and openings with a cloth or other mate-•
rial.
Never install the apparatus near heat sources such as radia-•
tors, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not place the product in direct sunlight or close to a sur-•
face directly heated by the sun.
Lightning
Never use this apparatus, or connect/disconnect communication
cables or power cables during lightning storms.
Dust
Do not operate the apparatus in areas with high concentration of
dust.
Vibration
Do not operate the apparatus in areas with vibration or place it
on an unstable surface.
Power Connection and Hazardous Voltage
The product may have hazardous voltage inside. Never attempt •
to open this product, or any peripherals connected to the
product, where this action requires a tool.
This product should always be powered from an earthed power •
outlet.
Never connect attached power supply cord to other products.•
In case any parts of the product has visual damage never •
attempt to connect mains power, or any other power source,
before consulting service personnel
The plug connecting the power cord to the product/power sup-•
ply serves as the main disconnect device for this equipment.
The power cord must always be easily accessible.
Route the power cord so as to avoid it being walked on or •
pinched by items placed upon or against it. Pay particular at-
tention to the plugs, receptacles and the point where the cord
exits from the apparatus.
Do not tug the power cord•
If the provided plug does not fit into your outlet, consult an •
electrician.
Never install cables, or any peripherals, without first unplug-•
ging the device from it’s power source.
Servicing
Do not attempt to service the apparatus yourself as opening or
removing covers may expose you to dangerous voltages or other
hazards, and will void the warranty. Refer all servicing to qualified
service personnel.
Unplug the apparatus from its power source and refer servicing to
qualified personnel under the following conditions:
If the power cord or plug is damaged or frayed •
If liquid has been spilled into the apparatus•
If objects have fallen into the apparatus •
If the apparatus has been exposed to rain or moisture •
If the apparatus has been subjected to excessive shock by •
being dropped
If the cabinet has been damaged•
If the apparatus seems to be overheated •
If the apparatus emits smoke or abnormal odor•
If the apparatus fails to operate in accordance with the •
operating instructions.
Accessories
Use only accessories specified by the manufacturer, or sold with
the apparatus.
Communication Lines
Never touch uninstalled communication wires or terminals un-•
less the telephone line has been disconnected at the network
interface.
Do not use communication equipment to report a gas leak in •
the vicinity of the leak.
To reduce the risk of fire, use only No. 26 AWG or larger tele-•
communication line cord (ISDN cables).
Product Approvals
Information about product approvals and CE declarations are
found in the Product Approvals in the Appendices section.
Safety Instructions
14
Quick
Setup
Using
the MPS
System
Status
System
Configuration
Installation
Gateway
Configuration
MCU
Configuration
Technical
Descriptions
Appendices
Main
Introduction