Filter
Top Products
xi
Installation Requirements and Handling
Temperature and Humidity Conditions
Temperature range: 50 to 86°F (10 to 30°C)
Humidity range: 20 to 80 % RH (no condensation)
IMPORTANT
Protecting the machine from condensation
To prevent condensation from forming inside the machine
in the following cases, let the machine adjust to the ambient
temperature and humidity for at least two hours before use.
When the room where the machine is installed is heated
rapidly
When the machine is moved from a cool or dry location to
a hot or humid location
If water droplets (condensation) form inside the machine,
this can result in paper jams or poor print quality.
When using an ultrasonic humidi er
When you are using an ultrasonic humidi er, it is therefore
recommended that you use puri ed water or other water that
is free of impurities.
If you use tap water or well water, impurities in the water will
be dispersed through the air. This can be trapped inside the
machine, causing degradation in print quality.
Power Supply Requirements
120 to 127 V 60 Hz
IMPORTANT
Precautions when connecting the power cord
Do not connect this machine to an uninterruptible power
source.
Use an AC power outlet exclusively for the machine. Do not
use the other sockets of the AC power outlet.
Do not plug the power plug into the auxiliary outlet on a
computer.
Do not use the same AC power outlet for both the machine
and any of the following equipment.
Copy machine
Air conditioner
Shredder
Equipment that consumes a large amount of electricity
Equipment that generates electrical noise
When unplugging the power cord, keep interval of 5 sec-
onds or more before plugging it again.
Miscellaneous precautions
The maximum power consumption of the machine is as
follows.
MF8350Cdn: 1,200 W or less
MF8050Cn: 900 W or less
Electrical noise or a dramatic drop in mains voltage may
cause the machine or computer to operate incorrectly or
lose data.
•
•
•
-
-
•
•
•
•
-
-
-
-
-
•
•
-
-
•
Installation Requirements
A location with su cient space
A location with good ventilation
A location with a at, even surface
A location able to fully support the weight of the machine
IMPORTANT
Do not install the machine in the following locations, as
this may result in damage to the machine.
A location subject to dramatic changes in temperature or
humidity
A location subject to condensation
A poorly ventilated location
(If you use the machine for a long time or to perform a large
amount of printing in a poorly ventilated room, the ozone
or other odors generated by the machine may create an
uncomfortable working environment. In addition, chemical
particles are dispersed during printing; therefore, it is impor-
tant to provide adequate ventilation.)
A location near equipment that generates magnetic or elec-
tromagnetic waves
A laboratory or location where chemical reactions occur
A location exposed to salt air, corrosive gases, or toxic gases
A location, such as on a carpet or mat, that may warp from
the weight of the machine or where the machine is liable to
sink
Installation Space
Required installation space
MF8350Cdn
Front View
Paper
cassette
Feeder cover
Feeder
Rear cover
in. (mm)
4
(100)
4
(100)
4
(100)
4
(100)
4
(100)
52 1/4 (1327)
26 3/4 (679)
37 1/2 (951)
33 1/2 (851)
MF8050Cn
Front View
Paper
cassette
Feeder cover Feeder
Rear cover
in. (mm)
48 3/8 (1229)
4
(100)
4
(100)
4
(100)
4
(100)
4
(100)
26 1/2 (674)
31 1/2 (801)
•
•
•
•
•
•
•
•
•
•
•
In order to use this machine in a safe and trouble-free manner, install the machine in a place that ful lls the following conditions.
Also, read the remarks carefully.