Filter
Top Products
Machine Characteristics
7
1 Machine Characteristics
1-1 Machine Description
The SEAL 44 Ultra laminator is an electro-mechanical device basically containing two siliconized
laminating rollers, two siliconized pull rollers and a top and bottom film unwind. Only the top roller is
heated. There are three temperature ranges; the speed can be set to any value between zero and
maximum speed. There is a set of nip values to accommodate for the various panel thicknesses.
The machine runs on a single-phase power supply.
The machine is able to perform the following processes:
• cold/hot mounting
• cold/hot laminating
• mounting & laminating in one pass
• decaling
• encapsulating
Process results can be controlled by:
• the temperature setting
• the speed setting
• the unwind tension of the film(s)
The SEAL 44 Ultra meets the Machinery Directive (89/392/EEC & applicable amendments). The
Notified Body’s TRF report (based on EN60950) is available.
It is ETL and cETL listed per directive UL 1950 3
rd
Edition 1995 and CAN/CSA C22.2 No. 950-95.
1-2 Identification
The machine identification label is located on the rear side of the machine.
The machine is available in two different voltages: 110VAC 50/60Hz and 230VAC 50/60Hz, see the
labels below.
• EQUIPMENT TO BE CONNECTED TO EARTHED MAINS OUTLET
ONLY.
• TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE COVER.
• NO OPERATOR SERVICEABLE PARTS INSIDE.
• REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
• CONECTAR EL PRODUCTO A RED DE ALIMENTACION CON TOMA DE TIERRA.
• PARE EVITAR UNA DESCARGA ELECTRICA, NO QUITE LA CUBIERTA.
• NO HAY PIEZAS REPARABLES POR EL USUARIO EN EL INTERIOR.
• REPARACIONES: CONTACTAR CON PERSONAL DE SERVICIO AUTORIZADO.
MODEL: SEAL 44 ULTRA
POWER SUPPLY: 110VAC 50/60Hz
CURRENT: 16A
SERIAL NO:
MANUFACTURED:
Hunt Graphics Europe BV
Kanaaldijk O.Z. 3, P.O.B. 29
8100AA Raalte, The Netherlands
EN 60950
EN 50081-1
EN 50082-1
FCC Part 15 (Class B)
MADE IN HOLLAND
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
• EQUIPMENT TO BE CONNECTED TO EARTHED MAINS OUTLET
ONLY.
• TO PREVENT ELECTRIC SHOCK, DO NOT REMOVE COVER.
• NO OPERATOR SERVICEABLE PARTS INSIDE.
• REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
• CONECTAR EL PRODUCTO A RED DE ALIMENTACION CON TOMA DE TIERRA.
• PARE EVITAR UNA DESCARGA ELECTRICA, NO QUITE LA CUBIERTA.
• NO HAY PIEZAS REPARABLES POR EL USUARIO EN EL INTERIOR.
• REPARACIONES: CONTACTAR CON PERSONAL DE SERVICIO AUTORIZADO.
MODEL: SEAL 44 ULTRA
POWER SUPPLY: 230VAC 50/60Hz
CURRENT: 9A
SERIAL NO:
MANUFACTURED:
Hunt Graphics Europe BV
Kanaaldijk O.Z. 3, P.O.B. 29
8100AA Raalte, The Netherlands
EN 60950
EN 50081-1
EN 50082-1
FCC Part 15 (Class B)
MADE IN HOLLAND
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS
SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT
CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.