Filter
Top Products
DLA-G150CLU
DLA-G150CLE
1-35
No.51931
69
Warning Messages
ENGLISHDEUTSHFRANÇAISITALIANOESPAÑOL
Memo
The message display language corresponds to the menu display language setting. This is set to “English (English)” when the
projector is bought. The display language can be selected from 6 languages. (Refer to page 46.) However, the input mode
(PC1, PC2, DVI, Y/C, VIDEO, COMP) and button indications (FREEZE, D.ZOOM, EXIT) are only displayed in English
irrespective of the display language setting.
The language settings in the section are explained in “English”.
Displayed when the lamp control
setting is set to LIGHT OUTPUT
CONTROL MODE (LOC) or LIGHT
POWER CONTROL MODE (LPC)
and the lamp use time display is
turned [ON] with the OSD menu
• Displayed when the lamp use
time exceeds 1000 hours.
* The message does not appear if
the lamp use time display is
turned [OFF] with the OSD menu.
• Arrange for a new lamp (lamp
unit) or replace the lamp early.
44, 46
Displayed when the lamp control
setting is set to LIGHT OUTPUT
CONTROL MODE (LOC) or LIGHT
POWER CONTROL MODE (LPC)
• Appears every time the projector
is turned on after the lamp use
time has exceeded 1900 hours
and until it reaches 2000 hours.
* The message is cleared by
pressing any button.
• Arrange for a new lamp (lamp
unit) or replace the lamp early.
44, 46
Displayed when the lamp control
setting is set to LIGHT OUTPUT
CONTROL MODE (LOC) or LIGHT
POWER CONTROL MODE (LPC)
• When the lamp use time reaches
2000 hours, the word “Warning”
blinks on the screen.
* To cancel this message, press
the EXIT button.
However, the same message will
appear every hour.
* If the power is turned off after the
lamp use time has exceeded
2000 hours, the power can not be
turned on again.
* When the lamp use time reaches
2010 hours, the projector is
forcibly turned off and can not be
turned back on again.
• Replace with a new lamp (lamp
unit) and reset the lamp use time.
44, 46
Message Cause Corrective action Page
EXIT
1000 h
Lamp replacement
EXIT
Lamp replacement
EXIT
Warning
Lamp replacement
68
Warning Messages
• When the DIGITAL ZOOM button
is pressed for the video signals
that cannot be zoomed (UXGA
60Hz, SXGA 60Hz.), this
message appears for a few
seconds to notify that the image
cannot be digitally zoomed.
* To forcibly clear the message,
press the EXIT button.
• Digital-zoom function does not
work for the inputted video
signals.
To use the this function, input the
video signals that can be digitally
zoomed.
13, 37
Displayed when the lamp control
setting is set to NORMAL MODE
• Appears every time the projector
is turned on after the lamp use
time has exceeded 900 hours and
until it reaches 1000 hours.
* The message is cleared by
pressing any button.
• Arrange for a new lamp (lamp
unit) or replace the lamp early.
44, 46
Displayed when the lamp control
setting is set to NORMAL MODE
• When the lamp use time reaches
1000 hours, the word “Warning”
blinks on the screen.
* To cancel this message, press
the EXIT button.
However, the same message will
appear every hour.
* If the power is turned off after the
lamp use time has exceeded
1000 hours, the power can not be
turned on again.
* When the lamp use time reaches
1010 hours, the projector is
forcibly turned off and can not be
turned back on again.
• Replace with a new lamp (lamp
unit) and reset the lamp time.
44, 46
Message Cause Corrective action Page
D.ZOOM
EXIT
Lamp replacement
EXIT
Warning
Lamp replacement