Toshiba e-STUDIO451c Copier User Manual


 
June 2005 © TOSHIBA TEC e-STUDIO281c/351c/451c ERROR CODE AND SELF-DIAGNOSTIC MODE
2 - 5
2
EA10 Finisher jam
(Finisher section)
Paper transport delay jam: The paper which has
passed the bridge
unit does not reach the inlet sensor. [MJ-1022/
1023/1024]
Ch.5.1.7 [ 2 ]
EA20 Paper transport stop jam:
(1) The paper does not pass through the inlet sen-
sor.
[MJ-1022/1023/1024]
(2) The paper has passed through the inlet sensor
but does not reach or pass the feed path sensor
or processing tray sensor.
[MJ-1023/1024]
Ch.5.1.7 [ 2 ]
EA30 Power-ON jam:
(1) Paper exists at the inlet sensor when power is
turned ON.
[MJ-1022/1023/1024]
(2) Paper exists at the feed path sensor or pro-
cessing tray sensor when power is turned ON.
[MJ-1023/1024]
Ch.5.1.7 [ 2 ]
EA40 Finisher jam
(Finisher section)
Door open jam:
1) The finisher has been released from the equip-
ment during printing. [MJ-1022]
2) The upper/front cover of the finisher section or
the upper/ front door of the puncher section has
opened during printing. [MJ-1023/1024]
Ch.5.1.7 [ 2 ]
EA50 Stapling jam: Stapling is not performed properly.
[MJ-1022/1023/1024]
Ch.5.1.7 [ 2 ]
EA60 Early arrival jam: The inlet sensor detects the paper
earlier than a specified timing. [MJ-1022/1023/
1024]
Ch.5.1.7 [ 2 ]
EA70 Stack delivery jam: It cannot deliver the stack of
paper on the intermediary process tray to the stack
tray. [MJ-1022]
Ch.5.1.7 [ 2 ]
EA80 Finisher jam
(Saddle stitcher sec-
tion)
Stapling jam: Stapling is not performed properly.
[MJ-1024]
Ch.5.1.7 [ 3 ]
EA90 Door open jam: The delivery cover or inlet cover
has opened dur-ing printing [MJ-1024].
Ch.5.1.7 [ 3 ]
EAA0 Power-ON jam: Paper exists at No.1 paper sensor,
No. 2 paper sensor, No.3 paper sensor, vertical
path paper sensor or delivery sensor when power is
turned ON. [MJ-1024]
Ch.5.1.7 [ 3 ]
EAB0 Transport stop jam: The paper which passed
through the inlet sensor does not reach or pass
No.1 paper sensor, No. 2 paper sensor, No.3 paper
sensor or delivery sensor. [MJ-1024]
Ch.5.1.7 [ 3 ]
EAC0 Transport delay jam: The paper which has reached
the inlet sensor does not pass through the inlet sen-
sor. [MJ-1024]
Ch.5.1.7 [ 3 ]
EAD0 Other paper jam Print end command time-out jam: The printing has
not finished normally because of the communica-
tion error between the SYS board and LGC board
at the end of printing.
Ch.5.1.7 [ 5 ]
EAE0 Finisher jam Receiving time time-out jam: The printing has been
interrupted because of the communication error
between the equipment and finisher when the
paper is transported from the equipment to the fin-
isher.
Ch.5.1.7 [ 5 ]
Error code Classification Contents Troubleshooting