Filter
Top Products
1
Index
1
1 second voice messages............................7-2
1/2 second voice messages.........................7-2
2
2 of 5 Code ...............................................2-12
default length setting........................... 2-13
enabling check digit ............................2-13
susceptible to mis-reads......................... 2-13
2 of 5 Codes
reading variable length bar codes ....... 2-13
2 of 5 Length ............................................ 2-13
4
4 digit year option ....................................2-15
4 second laser beam.................................. 2-17
6
6 beeps on power up...................................8-4
A
access point location...................................4-1
access point scan results............................. 4-2
Accumulate Mode ..................................... C-6
numeric barpad table............................ C-6
ActiveX drop-in component.......................6-1
ActiveX programming ...............................6-4
Advanced Features/Functions for
Code 39................................................. C-4
AIAG ......................................................... C-3
aiming dot................................................... J-2
Aiming Dot Duration ...............................2-17
aiming dot enabling.................................... J-3
Array examples for VB ..............................6-3
ASCII Code Equivalent Table ................. M-1
Authentication ............................................2-6
automatic check back .................................2-9
Automobile ID reading .............................. J-3
Automobile windshield reading................. J-3
Avoiding substitutions in scanning ............. 2-17
B
B11 Rubber Boot for Integrated Laser RF
Terminal ................................................L-4
Backlight Display.......................................2-7
Backlight Duration .....................................2-7
Bar Code ID's ...........................................2-12
Bar Code Menu Only setup parameters..... 2-1
bar code symbol .........................................2-4
Bar Code Type identification...................2-11
Bar Codes
Accumulate Mode ................................ C-6
default settings....................................... 2-2
ID character prefix ..............................2-11
Base Shut Down......................................... 6-5
Basic RF System communications.............3-1
Batteries....................................................2-14
battery charging.......................................... 1-4
Battery Life indicator................................. 1-3
Battery Status indicator............................ 2-15
Baud Rate for serial printer...................... 2-18
Beep Tone................................................. 2-14
Beeping
and Accumulate Mode ......................... C-6
changing the tone or pitch...................2-14
during setup configuration....................... 2-2
Beeping a lost unit...................................... 3-3
Before you begin programming................. 5-1
BEGIN key
transmitting ASCII 23 to host ...............6-6
bright light problems
aiming dot...............................................J-3
C
Cable pin-outs ........................................... A-1
Cables
needed for voice message cloning ........7-5
Cables for Zebra Cameo Printer................. A-1
Cameo Printer...........................................6-17
Cameo Printer Pin-outs .............................. A-1
Cannot Communicate with PIC Processor.8-3
Caps Lock ON
Code 39 setup parameter..................... 2-10
CCD pin-outs.............................................A-1
Change Batteries ........................................ 8-3
CHANGE BATTERIES.............................1-3
changing a host prompt already sent..........2-9
Changing a prompt..................................... 3-3
Changing more than one setup parameter at
a time using the bar coded setup menu.2-3
Changing the AA batteries on the RF
Terminal ................................................1-4
Changing the default voice messages ........7-4
Changing the Device IP Address............... 2-5
Changing the RF Terminals automatic shut-
off time ................................................2-16
Changing the Starting Channel ..................2-5
Changing the Subnet Mask .................2-5, 2-6
Changing the voice message partitions......7-2
charging batteries in RF Terminal .............1-4
Check Character Code 39.......................... C-4
Check digits / Checksums
and Accumulate Mode ......................... C-6
Check Digits / Checksums for Code 128...F-1
Code 39................................................. C-4