Filter
Top Products
5
Sequence error - avoiding ..........................3-3
Sequence Error ...........................................8-3
Serial printer setup paramters on terminal2-18
Server Communications
using the 802 Test program...................6-5
Server IP Address.......................................2-5
Server Not Available..................................8-3
Server not Available message ....................3-2
Server Re-initialized...................................8-3
Server Shut Down ......................................8-3
Set Date ....................................................2-15
Set Time ...................................................2-15
Setup for RF Terminal ...............................2-5
Setup Cloning to other terminals ...............7-4
Setup Menu
"Reset" bar code ..................................2-17
Baud Rate ............................................2-18
Data Bits..............................................2-18
Parity ...................................................2-18
RF Terminal parameters........................2-5
Stop Bits ..............................................2-18
SETUP MODE
using to program voice messages .........7-2
SETUP MODE Menu Option ....................1-4
Setup or playback voice messages............. 7-3
Shared Key Authentication ........................2-6
shelf label printing....................................6-18
Shut Down Time ......................................2-16
Shut Down Time feature............................ 1-1
SIGN OUT - missing the message............. 5-2
signal strength of access points..................4-2
Signing In, Data Structures, Transactions,
and State Management ..........................6-2
Signing out in mid-transaction...................... 5-2
SITE SURVEY Menu Option.................... 1-4
site survey results .......................................4-2
Six beeps on power up ...............................8-4
Skip Opening Screens ................................2-7
SPEAKER VOLUME................................ 2-8
SSID ...........................................................2-6
Stand mode...........See hands free laser scanning
Start Setup - scanning to enter Setup mode2-2
Start/stop characters
transmitting for Codabar........................ 2-12
transmitting for Code 39 .....................2-10
Starting Channel......................................... 2-5
STATUS key
reserved for date/time only ...................6-6
using to determine battery life .............. 8-2
Steps for installation...................................1-1
STK bar code............................................. 2-12
Stop Bits for serial printer........................ 2-18
Storage Tek bar code.................................. 2-12
Storage Tek Tape Label code ..................... 2-11
Subnet Mask............................................... 2-5
substitution errors....................................... J-2
Substitutions of data................................... J-3
sunlight problems, aiming dot.................... J-3
T
T49 Holster for RF Terminal .....................L-3
Tape library bar code.................................. 2-12
terminal cycles power ................................8-4
terminal goes back to opening screen ........8-4
Terminal keys
transmitting ASCII values.....................2-6
Terminal Out of Range Message ...............3-2
Terminal setup Encryption Key................. 2-6
Terminal Setup Cloning
to other terminals...................................7-4
Terminal Tracking...................................... 6-6
Time Set ................................................... 2-15
Tips for Using Voice Prompts ................... 7-1
Transaction examples for VB .................... 6-3
Transmission Delayed................................8-3
Transmitting Bar Code ID's .....................2-12
Transmitting Codabar start and stop characters2-12
Transmitting EAN-8/UPC-E in original
formats................................................. 2-11
Transmitting through walls........................... 4-2
TriOptic Code 39....................................... 2-11
Troubleshooting .........................................8-1
Turning on the R/F Terminal .....................1-1
turns off and on by itselt............................. 8-4
U
UCC 128 Serial Shipping Container bar
code .......................................................F-2
UCC/EAN Code 128
enabling/disabling ...............................2-11
UCC-128/ EAN-128...................................F-1
UP ARROW key
transmitting ASCII 28 to host ...............6-6
UPC 2 and 5-character supplemental codesH-2
UPC/EAN................................................. 2-10
about .....................................................H-1
Check digit ...........................................H-1
compressed format............................... 2-11
default settings...................................... 2-10
guidelines for use .................................. H-2
NSC and check digit............................2-11
NSC's and check digits.......................... 2-10
numbering conventions......................... H-2
supplemental codes ............................... 2-10
UPC-A - adding a country code............. 2-10
UPC-A in 13 digit EAN format............. 2-10
UPC/EAN check digits
enabling transmission of .....................2-11
UPC/EAN checksum character................. H-3
UPC/EAN Specifications ..........................H-1
UPC/EAN Supplements
enabling/disabling................................. 2-10
UPC-E Checksum Calculation.................. H-4
UPC-E0 and UPC-E1...............................2-11
UPC-E1 - enabling reading of..................2-12
Updating firmware .................................... B-1