Filter
Top Products
8. Programmable Features
83
k and l on the handset are not displayed
properly, the line mode selection is incorrect. Set
line mode to “A”.
{1} “A”
{2} “B” (default)
Note:
L You can also program this feature with the
handset (feature 0531 or feature 0532 on
page 89).
{#}{6}{7} Setting the incoming message
monitor
To hear an incoming message (ICM) from the
speaker when the answering machine is
recording the message.
{1} “ON” (default): You can monitor the incoming
message.
{2} “OFF”: Deactivates this feature.
LINE 1:{#}{7}{2}{*} LINE 2:{#}{7}{2}{#}
Setting flash time
The flash time depends on your telephone
exchange or host PBX.
{1} “90ms”
{2} “100ms”
{3} “110ms”
{4} “250ms”
{5} “300ms”
{6} “400ms”
{7} “600ms”
{8} “700ms” (default)
Note:
L The setting should stay at 700 ms unless
pressing {FLASH/CALL WAIT} fails to pick
up the Call Waiting call.
L If the unit is connected via a PBX, PBX
functions (transferring a call etc.) might not
work correctly. Consult your PBX supplier for
the correct setting.
L You can also program this feature with the
handset (feature 0521 and feature 0522 on
page 89).
{#}{7}{3} Setting the incoming call tone
This tone lets you know when a call is being
received on the other line, during a conversation
on the base unit.
{1} “OFF”: Deactivates this feature.
{2} “2” (default): The tone will sound 2 times.
{3} “ON”: The tone will sound for as long as the
line rings.
Note:
L You can also program this feature with the
handset (feature 0*2 on page 90).
{#}{7}{4} Setting room monitor
{1} “ON”
{2} “OFF” (default)
See page 53 for details.
Note:
L You can also program this feature with the
handset (feature 0*3 on page 90).
{#}{7}{5} Setting the Caller ID number auto
edit feature
{1} “ON” (default)
{2} “OFF”
See page 47 for details.
{#}{7}{6} Setting the connecting tone
If you often have trouble when sending faxes,
this feature allows you to hear connecting tones:
fax tone, ring back tone and busy tone. You can
use those tones to confirm the status of the other
party’s machine.
{1} “ON” (default): You will hear connecting
tones.
{2} “OFF”: Deactivates this feature.
Note:
L If the ring back tone continues, the other
party’s machine may not be a fax machine or
may have run out of paper. Check with the
other party.
L The connecting tone volume cannot be
adjusted.
LINE 1:{#}{7}{7}{*} LINE 2:{#}{7}{7}{#}
Changing the receiving mode in the AUTO
ANSWER setting
{1} “TAM/FAX” (default): Telephone Answering
Machine/Fax mode (page 59)
{2} “FAX ONLY”: Fax only mode (page 60)
{3} “TAM ONLY”: Telephone Answering
Machine only mode (page 61)
Note:
L When the unit is set to TAM ONLY mode,
friendly reception (feature #46* and feature
#46# on page 82) will turn OFF automatically.
When you change the unit from TAM ONLY
mode to TAM/FAX mode or FAX ONLY mode,
friendly reception will be turned ON
automatically.
{#}{8}{0} Resetting advanced features to
their default settings
{1} “YES”
{2} “NO” (default)
To reset the advanced features:
1. Press {MENU}.
2. Press {#}, then {8}{0}.
FG6550-PFQX2225ZA-en.book Page 83 Monday, August 8, 2005 8:16 PM