Filter
Top Products
Copying_ 60
1. Place a single original face down on the scanner glass and close the
scanner lid. (See "Loading originals" on page 36.)
2. Press Copy from the main screen.
3. Select th
e tray in Paper Supply.
4. Pr
ess the Advanced tab > Clone Copy.
This feature is available only when the options in the Basic tab are
selected as below;
• Duplex to 1 ->
1 Sided
• Reduce/Enlarge to Original (100%)
• Paper Supply to Tray.
5. Pr
ess On to activate this feature.
6. Pr
ess OK.
7. Pr
ess Start on the control panel to begin copying.
Book copying
Use this feature to copy a book. If the book is too thick, lift the scanner lid
until its hinges are engaged by the stopper and then close the scanner lid. If
the book or magazine is thicker than 30 mm (1.18 inches), start copying with
the scanner lid open.
This copy feature is available only when you place originals on the scanner
glass.
1. Place the originals face down on the scanner glass and close the
scanner lid.. (See "Loading originals" on page 36.)
2. Pr
ess Copy from the main screen.
To remove shadows of a book edge, press the Image tab > Edge
Erase > Book Center and Edges Erase.
3. Press the Advanced tab > Book Copy.
4. Select th
e appropriate option.
• Off: Disables this feature.
• Left
Page: Prints left page of the book.
• Right Page: Prints right page of the book.
• Both Page
: Prints both facing pages of the book.
5. Pr
ess OK.
6. Pr
ess Start on the control panel to begin copying.
Booklet copying
The machine automatically prints on one or both sides of the paper, which
are then folded to produce a booklet with all of the pages in the correct
sequence.
The machine will also reduce and correctly adjust the position of each
image to fit on the selected paper.
1. Place the originals face up in the document feeder. Or place a single
original face down on the scanner glass and close the scanner lid. (See
"Loading originals" on page 36.)
2. Pres
s Copy from the main screen.
3. Select the tray
in Paper Supply.
4. Pre
ss the Advanced tab > Booklet.
5. Pres
s On to use this feature, and select detailed settings for each
option.
• 1 Si
ded Original: Copies on one side of originals.
• 2 Si
ded Original: Copies on both sides of originals.
6. Pres
s OK.
7. Pres
s Start on the control panel to begin copying.
This feature is possible only with A4, Letter, Legal, Folio, Oficio, JIS
B5, ISO B5, Executive, A5 and Statement sized paper.
Cover copying
The machine automatically adds covers to your copied set using stock taken
from a different tray. Covers must be the same size and orientation as the
main body of the job.
1. Pl
ace the originals face up in the document feeder. Or place a single
original face down on the scanner glass and close the scanner lid. (See
"Loading originals" on page 36.)
2. Pres
s Copy from the main screen.
3. Select the tray
in Paper Supply.
4. Pre
ss the Advanced tab > Covers.
Once you have set the Paper Supply option to Auto, you cannot
use this feature.
5. Press On to use this feature, and select detailed settings for each
option.
• Position: Selects whether the cover will be placed at the front,
back, or both.
• C
over Sheet: Selects whether the cover will be 1 sided, 2 sided, or
blank paper.
• Pa
per Source: Select the paper tray, where the cover sheet is
loaded.
6. Press OK.
7. Pres
s Start on the control panel to begin copying.
Transparency copying
When you prepare transparencies for presentations, use this feature to copy
the information.
Before you start this special copy job, set the tray's Paper Types and
Paper Size to Transparency. (See "Setting the paper size and type"
on page 42.)
1. Pla
ce the originals face up in the document feeder. Or place a single
original face down on the scanner glass. (See "Loading originals" on
page 36.)
2. L
oad the right-sized transparencies into the tray you have set.
3. Se
t the paper type to Transparency.
4. Pres
s Copy from the main screen.
5. Pre
ss the Advanced tab > Transparencies.
6. Select T
ransparencies option.
• No Separa
tor: Does not place separator sheets between
transparencies.
• B
lank Sheet: Places a blank sheet between transparencies.