Filter
Top Products
9. Multi-unit Operation
59
9 Multi-unit OperationAdditional Units
9.1 Operating additional units
9.1.1 Additional cordless handsets
Up to 6 cordless handsets can be registered to a single
base unit. Additional cordless handsets will give you the
freedom to, for example, have an intercom call with
another cordless handset while a third cordless handset
is on an outside call.
Important:
L The additional cordless handset model
recommended for use with this unit is noted on
page 9. If other model cordless handset is used,
certain operations (cordless handset settings,
base unit settings, etc.) may not be available.
9.1.2 Additional base units
Cordless handsets can be registered to up to 4 base
units, allowing you to add additional base units and
extend the area in which your cordless handset(s) can
be used. If a cordless handset moves out of range of its
base unit when “Auto” is selected on base unit
selection (page 59), it will look for another base unit to
make or receive calls. A base unit and the cordless
handsets it communicates with is called a “radio cell”.
Note:
L Calls will be disconnected when the cordless
handset moves from one radio cell to another.
9.2 Registering a cordless
handset to a base unit
The included cordless handset and base unit are
preregistered. If for some reason the cordless handset is
not registered to the base unit (for example, w flashes
even when the cordless handset is near the base unit),
register the cordless handset manually.
After purchasing an additional cordless handset, register
it to the base unit. Ensure that the additional cordless
handset is switched ON. If it is not ON, press and hold
{ih} for few seconds to turn the cordless handset ON.
1 " i N i #
2 “Registration” i #
3 “Register H.set” i #
4 Select a base unit number. i #
L This number is used by the cordless handset as
a reference only.
5 Press and hold {LOCATOR} on the base unit for
about 3 seconds, until the registration tone sounds.
L After pressing {LOCATOR}, the rest of this
procedure must be completed within 1 minute.
6 Wait until “Enter Base PIN” is displayed, then
enter the base unit PIN (default: “0000”), then press
#.
L If you forget your PIN, consult your nearest
Panasonic service centre.
L When the cordless handset has been registered
successfully, w will stop flashing. If keytones are
turned ON (page 56), a confirmation tone will be
heard.
Note:
L Charge the batteries of your additional cordless
handset for about 7 hours before initial use.
9.2.1 Selecting a base unit
When “Auto” is selected, the cordless handset will
automatically use any available base unit it is registered
to. When a specific base unit is selected, the cordless
handset will make and receive calls using that base unit
only. If the cordless handset is out of range of that base
unit, no calls can be made.
1 " i N i #
2 “Select Base” i #
3 Select the desired base unit number, or “Auto”. i
#
L The cordless handset starts searching for the
base unit.
9.2.2 Cancelling a cordless handset
A maximum of 6 cordless handsets can be registered to
a base unit. A cordless handset can cancel its own
registration (or the registration of another cordless
handset) that is stored in the base unit. This will allow the
base unit to forget the cordless handset.
1 " i L i #
2 Enter “335”.
3 “Cancel Handset” i #
L The numbers of all cordless handsets registered
to the base unit are displayed.
4 Select the cordless handset(s) you want to cancel,
by pressing the desired cordless handset number.
i #
5 “Yes” i # i {ih}
9.2.3 Cancelling a base unit
A cordless handset can be registered to a maximum of 4
base units. A cordless handset can cancel a base unit
that it is registered to. This allows the cordless handset
to forget the base unit.
1 " i N i #
2 “Registration” i #
3 Enter “335”.
4 “Cancel Base” i #
5 Select the base unit(s) you want to cancel, by
pressing the desired base unit number. i #
6 “Yes” i # i {ih}
FC255AL-PFQX2639ZA-en.book Page 59 Friday, April 21, 2006 1:50 PM