Filter
Top Products
Rev.2.00 Nov 28, 2005 page 207 of 378
REJ09B0124-0200
M16C/6N Group (M16C/6NK, M16C/6NM) 16. A/D Converter
Under development
This document is under development and its contents are subject to change.
Figure 16.4 ADCON0 Register and ADCON1 Register in One-shot Mode
CH0
CH1
CH2
MD0
MD1
TRG
ADST
CKS0
0 0 : One-shot mode
(3)
0 : Software trigger
1 : ADTRG trigger
0 : A/D conversion disabled
1 : A/D conversion started
Refer to NOTE 2 for ADCON2
Register
Trigger Select Bit
A/D Conversion Start Flag
Frequency Select Bit 0
Analog Input Pin Select Bit
A/D Operation Mode
Select Bit 0
A/D Control Register 0
(1)
b7 b6 b5 b4 b3 b2 b1 b0
Bit Symbol
Bit Name Function
RW
RW
RW
RW
RW
RW
RW
RW
RW
Symbol Address After Reset
ADCON0 03D6h 00000XXXb
b4 b3
0 0 0 : AN0 is selected
0 0 1 : AN1 is selected
0 1 0 : AN2 is selected
0 1 1 : AN3 is selected
1 0 0 : AN4 is selected
1 0 1 : AN5 is selected
1 1 0 : AN6 is selected
1 1 1 : AN7 is selected
(2) (3)
b2 b1 b0
0
RW
RW
RW
RW
RW
RW
RW
RW
SCAN0
SCAN1
MD2
BITS
VCUT
OPA0
OPA1
CKS1
Bit Name Function
Bit Symbol
RW
Symbol Address After Reset
ADCON1 03D7h 00h
0 : 8-bit mode
1 : 10-bit mode
Set to "0" when one-shot mode
is selected
1 : VREF connected
Refer to NOTE 2 for ADCON2
Register
Invalid in one-shot modeA/D Sweep Pin Select Bit
8/10-Bit Mode Select Bit
VREF Connect Bit
(2)
A/D Operation Mode
Select Bit 1
External Op-Amp
Connection Mode Bit
Frequency Select Bit 1
0 0 :
ANEX0 and ANEX1 are not used
0 1 : ANEX0 input is A/D converted
1 0 : ANEX1 input is A/D converted
1 1 :
External op-amp connection mode
b7 b6 b5 b4 b3 b2 b1 b0
A/D Control Register 1
(1)
NOTES:
1. If the ADCON1 register is rewritten during A/D conversion, the conversion result will be indeterminate.
2. If the VCUT bit is reset from "0" (VREF unconnected) to "1" (VREF connected), wait for 1 µs or more before
starting A/D conversion.
b7 b6
10
0
NOTES:
1. If the ADCON0 register is rewritten during A/D conversion, the conversion result will be indeterminate.
2. AN0_0 to AN_7, and AN2_0 to AN2_7 can be used in same way as AN0 to AN7. Use the ADGSEL1 to ADGSEL0
bits in the ADCON2 register to select the desired pin.
3. After rewriting the MD1 to MD0 bits, set the CH2 to CH0 bits over again using another instruction.