Filter
Top Products
7. SUPPLY SPECIFICATIONS ENGLISH VERSION EO1-33089
7.1 Media
E7- 2
B-EX4T-TS12-QM-R [Unit: mm]
Cut mode
Rotary cutter
Label dispensing mode
Item
Batch mode Strip mode
Head-up disabled Head-up enabled
Disc cutter
Label 10.0 – 1500.0 25.4 – 256.0
3”/s.: 94.0 - 1500.0
5”/s.: 102.0 – 1500.0
8”/s.: 113.0 – 1500.0
38.0 – 1500.0
25.4 – 1500.0
c Media pitch
Tag 10.0 – 1500.0 ----
3”/s., 5”/s.: 30.0 – 1500.0
8”/s.: 38.0 – 1494.0
25.4 – 1500.0
d Label length 6.0 – 1498.0 23.4 – 1498.0
3”/s.: 81.0 – 1494.0
5”/s.: 89.0 – 1494.0
8”/s.: 100.0 – 1494.0
25.0 – 1494.0
23.4 – 1494.0
e Tag/Backing paper width 30.0 – 120.0 50.0 – 120.0 30.0 – 120.0
f Label width 27.0 – 117.0
g Gap length 2.0 – 20.0 6.0 – 20.0
h Black mark length (Tag paper) 2.0 – 10.0
i Max. effective print width 104.0 ±0.2
Label 6.0 – 1496.0 21.4 – 252.0
3”/s.:79.0 - 1492.0
5”/s.: 87.0 – 1492.0
8”/s.: 98.0 – 1492.0
23.0 – 1492.0
21.4 – 1492.0
j Effective print length
Tag 8.0 – 1498.0 ----
3”/s., 5”/s.: 28.0 – 1498.0
8”/s.: 36.0 – 1498.0
21.40 – 1498.0
k Print speed up/slow down area 1.0 (Slow down shall be 1.5 when the print speed is 14 ips.)
Label 0.08 – 0.17
Thickness
Tag 0.08 – 0.263 (30 to 50 mm width)
Maximum effective length for on the fly issue 749.0
Maximum outer roll diameter Ø200 (Ø180 when using the built-in Rewinder)
Roll direction Inside (standard)
Inner core diameter Ø76.2±0.3
N
OTES:
1. To ensure print quality and print head life use only TOSHIBA TEC specified media.
2. When the Rotary Cutter is used, the minimum label length differs depending on the print speed.
* When issuing a label at 3”/sec., label length shall be 91.0 mm – (Gap length/2) or longer.
* When issuing a label at 5”/sec., label length shall be 99.0 mm – (Gap length/2) or longer.
* When issuing a label at 6”/sec., label length shall be 103.0 mm – (Gap length/2) or longer.
* When issuing a label at 8”/sec., label length shall be 110.0 mm – (Gap length/2) or longer.
3. When the Disc cutter is used, the minimum label length shall be 18.0 mm – (Gap length/2) or longer.
4: When using the Rotary Cutter, be sure to install the Ribbon Saving Module (B-EX904-R-QM-R) to perform head-
up and cut. Failure to do this may cause a paper jam or ribbon error.
5: The Rotary Cutter and the Strip Module do not support the print speed of 10”/sec. or faster.
6. When you use tag paper which is narrower than 50 mm, turn the Head Lever to LABEL position.
7. The ratio of a label length to a gap length must be a minimum of 3 to 1 (3:1).
8. When using a label stock in cut mode, be sure to cut the gaps. Cutting labels will cause the glue to stick to the
cutter, which may affect the cutter performance and shorten the cutter life.