Filter
Top Products
142 AT-WR4500 Series - IEEE 802.11abgh Outdoor Wireless Routers
RouterOS v3 Configuration and User Guide
default - derive this value from the interface default profile; same as no if this is the interface default
profile
dns-server (IP address{1,2}) - IP address of the DNS server to supply to clients
idle-timeout (time) - specifies the amount of time after which the link will be terminated if there was no
activity present. There is no timeout set by default
0s - no link timeout is set
incoming-filter (name) - firewall chain name for incoming packets. Specified chain gets control for each
packet coming from the client. The ppp chain should be manually added and rules with action=jump
jump-target=ppp should be added to other relevant chains in order for this feature to work. For more
information look at the Examples section
local-address (IP address | name) - IP address or IP address pool name for PPP server
name (name) - PPP profile name
only-one (yes | no | default; default: default) - defines whether a user is allowed to have more then one
connection at a time
yes - a user is not allowed to have more than one connection at a time
no - the user is allowed to have more than one connection at a time
default - derive this value from the interface default profile; same as no if this is the interface default
profile
outgoing-filter (name) - firewall chain name for outgoing packets. Specified chain gets control for each
packet going to the client. The ppp chain should be manually added and rules with action=jump jump-
target=ppp should be added to other relevant chains in order for this feature to work. For more
information look at the Examples section
rate-limit (text; default: "") - rate limitation in form of rx-rate[/tx-rate] [rx-burst-rate[/tx-burst-
rate] [rx-burst-threshold[/tx-burst-threshold] [rx-burst-time[/tx-burst-time] [priority] [rx-
rate-min[/tx-rate-min]]]] from the point of view of the router (so "rx" is client upload, and "tx" is
client download). All rates are measured in bits per second, unless followed by optional 'k' suffix (kilobits
per second) or 'M' suffix (megabits per second). If tx-rate is not specified, rx-rate serves as tx-rate too.
The same applies for tx-burst-rate, tx-burst-threshold and tx-burst-time. If both rx-burst-threshold and
tx-burst-threshold are not specified (but burst-rate is specified), rx-rate and tx-rate are used as burst
thresholds. If both rx-burst-time and tx-burst-time are not specified, 1s is used as default. Priority takes
values 1..8, where 1 implies the highest priority, but 8 - the lowest. If rx-rate-min and tx-rate-min are not
specified rx-rate and tx-rate values are used. The rx-rate-min and tx-rate-min values can not exceed rx-
rate and tx-rate values.
remote-address (IP address | name) - IP address or IP address pool name for PPP clients
session-timeout (time) - maximum time the connection can stay up. By default no time limit is set
0s - no connection timeout
use-compression (yes | no | default; default: default) - specifies whether to use data compression or
not
yes - enable data compression
no - disable data compression
default - derive this value from the interface default profile; same as no if this is the interface default
profile
use-encryption (yes | no | required | default; default: default) - specifies whether to use data
encryption or not
yes - enable data encryption
no - disable data encryption
requided - enable and require encryption
default - derive this value from the interface default profile; same as no if this is the interface default
profile
use-vj-compression (yes | no | default; default: default) - specifies whether to use Van Jacobson header
compression algorithm
yes - enable Van Jacobson header compression
no - disable Van Jacobson header compression
default - derive this value from the interface default profile; same as no if this is the interface default
profile
wins-server (IP address{1,2}) - IP address of the WINS server to supply to Windows clients