Filter
Top Products
AT-WR4500 Series - IEEE 802.11abgh Outdoor Wireless Routers 43
RouterOS v3 Configuration and User Guide
[admin@AT-WR4562] interface wireless> print
Flags: X - disabled, R - running
0 R name="wlan1" mtu=1500 mac-address=00:0C:42:05:00:14 arp=enabled
interface-type=Atheros AR5413 mode=station ssid="AT-WR4560"
frequency=2412 band=2.4ghz-b/g scan-list=default antenna-mode=ant-a
wds-mode=disabled wds-default-bridge=none wds-ignore-ssid=no
default-authentication=yes default-forwarding=yes
default-ap-tx-limit=0 default-client-tx-limit=0 hide-ssid=no
security-profile=default compression=no
1 name="wlan2" mtu=1500 mac-address=00:80:48:41:AF:2A arp=enabled
interface-type=Atheros AR5413 mode=station ssid="AT-WR4560" frequency=2412
band=2.4ghz-b/g scan-list=default antenna-mode=ant-a wds-mode=disabled
wds-default-bridge=none wds-ignore-ssid=no default-authentication=yes
default-forwarding=yes default-ap-tx-limit=0 default-client-tx-limit=0
hide-ssid=no security-profile=default compression=no
[admin@AT-WR4562] interface wireless> set 0,1 mode=nstreme-dual-slave
Then add nstreme2 interface with exact-size framing:
[admin@AT-WR4562] interface wireless nstreme-dual> add \
\... framer-policy=exact-size
Configure which card will be receiving and which - transmitting and specify remote receiver card's MAC
address:
[admin@AT-WR4562] interface wireless nstreme-dual> print
Flags: X - disabled, R - running
0 X name="n-streme1" mtu=1500 mac-address=00:00:00:00:00:00 arp=enabled
disable-running-check=no tx-radio=(unknown) rx-radio=(unknown)
remote-mac=00:00:00:00:00:00 tx-band=5GHz tx-frequency=5180
rx-band=5GHz rx-frequency=5320 disable-csma=no
rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps
rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps
framer-policy=exact-size framer-limit=4000
[admin@AT-WR4562] interface wireless nstreme-dual> set 0 disabled=no \
\... tx-radio=wlan1 rx-radio=wlan2 remote-mac=00:0C:42:05:0B:12
[admin@AT-WR4562] interface wireless nstreme-dual> print
Flags: X - disabled, R - running
0 R name="n-streme1" mtu=1500 mac-address=00:0C:42:05:0B:12 arp=enabled
disable-running-check=no tx-radio=wlan1 rx-radio=wlan2
remote-mac=00:00:00:00:00:00 tx-band=5GHz tx-frequency=5180
rx-band=5GHz rx-frequency=5320 disable-csma=no
rates-b=1Mbps,2Mbps,5.5Mbps,11Mbps
rates-a/g=6Mbps,9Mbps,12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps
framer-policy=exact-size framer-limit=4000
[admin@AT-WR4562] interface wireless nstreme-dual>
4.3.5 Registration Table
Submenu level: /interface wireless registration-table
Description
In the registration table you can see various information about currently connected clients. It is used only
for Access Points.
Property Description
802.1x-port-enabled (read-only: yes | no) - whether the data exchange is allowed with the peer (i.e.,
whether 802.1x authentication is completed, if needed)
ack-timeout (read-only: integer) - current value of ack-timeout
ap (read-only: yes | no) - whether the connected device is an Access Point or not
ap-tx-limit (read-only: integer) - transmit rate limit on the AP, in bits per second
authentication-type (read-only: none | wpa-psk | wpa2-psk | wpa-eap | wpa2-eap) - authentication
method used for the peer
bytes (read-only: integer, integer) - number of sent and received packet bytes