Filter
Top Products
36 AT-WR4500 Series - IEEE 802.11abgh Outdoor Wireless Routers
RouterOS v3 Configuration and User Guide
band - operating band
2.4ghz-b - IEEE 802.11b
2.4ghz-b/g - IEEE 802.11g (supports also legacy IEEE 802.11b protocol)
2.4ghz-g-turbo - IEEE 802.11g using double channel, providing air rate of up to 108 Mbit
2.4ghz-onlyg - only IEEE 802.11g
5ghz - IEEE 802.11a up to 54 Mbit
5ghz-turbo - IEEE 802.11a using double channel, providing air rate of up to 108Mbit
2ghz-10mhz - variation of IEEE 802.11g with half the band, and, accordingly, twice lower speed (air rate
of up to 27Mbit)
2ghz-5mhz - variation of IEEE 802.11g with quarter the band, and, accordingly, four times lower speed
(air rate of up to 13.5Mbit)
5ghz-10mhz - variation of IEEE 802.11a with half the band, and, accordingly, twice lower speed (air rate
of up to 27Mbit)
5ghz-5mhz - variation of IEEE 802.11a with quarter the band, and, accordingly, four times lower speed
(air rate of up to 13.5Mbit)
basic-rates-a/g (multiple choice: 6Mbps, 9Mbps, 12Mbps, 18Mbps, 24Mbps, 36Mbps, 48Mbps, 54Mbps;
default: 6Mbps) - basic rates in 802.11a or 802.11g standard. This should be the minimal speed all the
wireless network nodes support (they will not be ableto connect otherwise). It is recommended to leave
this as default
basic-rates-b (multiple choice: 1Mbps, 2Mbps, 5.5Mbps, 11Mbps; default: 1Mbps) - basic rates in 802.11b
mode. This should be the minimal speed all the wireless network nodes support (they will not be ableto
connect otherwise). It is recommended to leave this as default
burst-time (time; default: disabled) - time in microseconds which will be used to send data without
stopping. Note that no other wireless cards in that network will be able to transmit data during burst-
time microseconds.
compression (yes | no; default: no) - if enabled on AP (in ap-bridge or bridge mode), it advertizes that it
is capable to use hardware data compression. If a client, connected to this AP, also supports and is
configured to use the hardware data compression, it requests the AP to use compression. This property
does not affect clients, which do not support compression.
country (albania | algeria | argentina | armenia | australia | austria | azerbaijan | bahrain | belarus | belgium
| belize | bolvia | brazil | brunei darussalam | bulgaria | canada | chile | china | colombia | costa rica | croatia
| cyprus | czech republic | denmark | dominican republic | ecuador | egypt | el salvador | estonia | finland |
france | france_res | georgia | germany | greece | guatemala | honduras | hong kong | hungary | iceland |
india | indonesia | iran | ireland | israel | italy | japan | japan1 | japan2 | japan3 | japan4 | japan5 | jordan |
kazakhstan | korea republic | korea republic2 | kuwait | latvia | lebanon | liechtenstein | lithuania |
luxemburg | macau | macedonia | malaysia | mexico | monaco | morocco | netherlands | new zealand |
no_country_set | north korea | norway | oman | pakistan | panama | peru | philippines | poland | portugal |
puerto rico | qatar | romania | russia | saudi arabia | singapore | slovak republic | slovenia | south africa |
spain | sweden | switzerland | syria | taiwan | thailand | trinidad & tobago | tunisia | turkey | ukraine |
united arab emirates | united kingdom | united states | uruguay | uzbekistan | venezuela | viet nam | yemen
| zimbabwe; default: no_country_set) - limits wireless settings (frequency and transmit power) to those
which are allowed in the respective country
no_country_set - no regulatory domain limitations
default-ap-tx-limit (integer; default: 0) - limits data rate for each wireless client (in bps)
0 - no limits
default-authentication (yes | no; default: yes) - specifies the default action on the client's side for APs
that are not in connect list or on the AP's side for clients that are not in access list
yes - enables AP to register a client if it is not in access list. In turn for client it allows to associate with
AP not listed in client's connect list
default-client-tx-limit (integer; default: 0) - limits each client's transmit data rate (in bps). Works only if
the client is also a Router
0 - no limits
default-forwarding (yes | no; default: yes) - whether to use data forwarding by default or not. If set to
'no', the registered clients will not be able to communicate with each other
dfs-mode (none | radar-detect | no-radar-detect; default: none) - used for APs to dynamically select
frequency at which this AP will operate
none - do not use DFS
no-radar-detect - AP scans channel list from "scan-list" and chooses the frequency which is with the
lowest amount of other networks detected